Panasonic WV-SW598 installation instructions Connection, 8P alarm cable connector

Page 26

Connection

Caution:

Before starting connections, make sure that the power connection (24 V AC power cord or LAN cable) is discon- nected. Failure to observe this may cause fire, electric shock, injury, or damage to the product.

A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE EQUIPMENT POWERED BY

24 V AC POWER SUPPLY.

Power cable

Brown

 

 

 

To the power supply (24 V AC±15 %, 50 Hz/60 Hz)

 

 

 

Blue

 

 

 

 

 

 

 

 

Green GND

LAN cable (category 5e or better)

To a PoE+ hub, PC, etc. Network cable with cable coupler

Output cable for the

 

monitor used for

 

adjustment

Coaxial cable

 

(BNC)

External I/O cable

8P alarm cable (accessory)

Microphone input cable (white)

To a plug-in power type microphone

Audio output cable (black)

To an external powered speaker

To the monitor used for adjustment

To a sensor

8P alarm cable connector

ALARM IN1/BLACK/WHITE IN (black) (Terminal 1)

GND (brown)

ALARM IN2/ALARM OUT (red) (Terminal 2)

GND (orange)

ALARM IN3/AUX OUT (yellow) (Terminal 3)

GND (light blue or green)

Unused (blue)

Unused (purple)

Output cable for the monitor used for adjustment The video output is set to NTSC in the default settings of the camera. If you want to change the video output setting to PAL, refer to the Operating Instructions on the provided CD-ROM.

Power cable

Connect the power cable to the 24 V AC power sup- ply using the 24 V AC power supply connector kit (accessory).

IMPORTANT:

The power supply of 24 V AC shall be insulated against 120 V AC (for U.S. and Canada) or 220 V - 240 V AC (for

Europe and other countries).

Do not cut or process the network cable since the power is superimposed when using a PoE+ device for power sup- ply. Besides, do not put an excessive weight on connected sections.

The network camera is only intended for a connection to an ethernet or PoE network without routing to the outside plant.

26

Image 26
Contents PGQX1224YA Cs0313-1043Can ICES-3A/NMB-3A Contents Important safety instructions Preface Disclaimer of warrantyLimitation of liability Main functions Intel CoreTM 2 Duo 2.4 GHz or faster recommended System requirements for a PCCPU Network security Trademarks and registered trademarksCopyright Precautions Turn the power off when cleaning this product Do not damage the power cableCorrectly perform all wiring This product has no power switchAbout SD memory card Periodically images on the screen appear to be dis- tortedWhat to do if Warming UP-PLEASE Wait appears on the display Code labelPosition refresh Tilt angles and the zoom ratioPrecautions for installation Time & date setting Check before installationPoE+ Power over Ethernet Plus Take notice of humidityMajor operating controls Main bodyOFF šON Step Turn off the power of the cameraInitialize the camera Insert/remove an SD memory card How to insert an SD memory cardWhen inserting an SD memory card, make sure the direction Remove the locking screw of the water-resistant capHow to remove the SD memory card Installations/Connections Power Source IEC/EN/UL/CSAHow to detach the housing base When using the wall mount bracket WV-Q122 option InstallationInstall the mounting bracket When using the mount bracket custom-madePlate spring Projection Dents Wire Detach the hooks Front/rear sunshields xing screw 8P alarm cable connector ConnectionHow to assemble the 24 V AC power supply con- nector kit AC power supply connector kit accessoryRecommended specification of cable wire Output cable for the monitor used for adjustmentMicrophone/line input cable External I/O cableRatings Audio output cableLAN cable category 5e or better, cross Connection exampleRequired cable LAN cable category 5e or better, straight Configure the network settings Configuring the camera so that it can be accessed from a PCPage Troubleshooting Power cable insulation is Damaged Live indicator keeps onLive indicator lights red Power cable, plugOperation status Indicator status About the live indicatorCamera when there are It is hard to see images withAlarm in 3 AUX OUT x1 each SpecificationsAlarm in 1 BLACK/WHITE IN/ Alarm in 2 Alarm OUT Terminal 1, Terminal 2, and TerminalLens ATW1/ ATW2/ AWCJpeg Mjpeg MLD, ICMP, ARPBB-HCA8A Standard accessoriesOptional accessories BB-HCA8CEPage Page Page Page Page Page Panasonic Corporation For business users in the European UnionFor U.S. and CanadaFor Europe and other countries Http//panasonic.net