Bosch Appliances PT-400 manual Data Entry After Selection of Receiver Point Type

Page 22

Security Escort Technical Reference Manual 3.0 System Menus

and Screens

EN 22

Use the receiver selection when there is a physical receiver connected at this bus location.

Figure 13: Data Entry After

Selection of Receiver Point

Type

Use the alert unit selection when there is an alert unit connected at this bus location.

Figure 14: Data Entry after Selection of Alert Unit Point Type

Use the virtual selection when there is no physical device connected at this bus location. Starting with version

2.03of the Security Escort software, you can add virtual receivers in the Transponder Database. A virtual receiver is added at one of the 64 points allowed per transponder. However, there is no physical hardware used.

The virtual receiver is intended to compensate in cases where there is a receiver imbalance. For example, if a building with a dense population of receivers is adjacent to a fence with few receivers and an alarm occurs between them, the alarm location can pull towards the building. The virtual receiver references two other physical receivers that must be on the same transponder. Only if both of the referenced receivers receive an alarm transmission, is the virtual receiver added to the alarm as if a physical receiver heard the alarm at the average receive level of the two referenced receivers. The virtual receiver’s location and sensitivity can be adjusted the same as a physical receiver. After a virtual receiver is added, verify the surrounding areas to make sure they were not adversely affected. In no event, should a virtual receiver be utilized as a cost savings measure to avoid the installation of an actual receiver.

Figure 16: Data Entry when Show Areas is Selected

Figure 15: Data Entry after Selection of Virtual Receiver Point Type

Bosch Security Systems 6/12 38947D

Image 22

Contents Security Escort You MAY Limited WarrantySoftware License Agreement You may notRemedy Table of Contents Figures Tables Subscriber Database AdvancedSecurity Escort System Architecture System ComponentsReceiver Maintenance TransmitterPoint Transmitter Alert UnitCentral Console TransponderSoftware Overview Transponder Scanning Alarm Sequence TransmitterSystem Operation Receiver’s ResponseOperator’s Response Central Console Response During AlarmSelected in the Security Preferences Central Console ScreenTest Sequence Transmitter Multiple AlarmsCentral Console Response System Menus and Screens Setting Up The SystemInitial System Configuration File MenuReports Database Subscriber DatabasePager ID Pager PasswordPhone Number Pager GroupAlarm on Shorted Loop Enable Reed SwitchDisable Shorted Loop Alarm When Armed, Trouble When Disarmed on Shorted LoopRequires Check-in Alarm GroupTransponder Area DoneTransponder ID Database RecordCreated, Modified, Modify Oper Comm Port IndexKill Transponder Insert NewEdit Data Delete PointTrouble Response Text Trouble Type TextTrouble Tamper Text Show Points+, -, Bus + and Bus Point TypeData Entry After Selection of Receiver Point Type Assigning Alert Units to Receivers If the Enable algorithm tweaks field isAlert 1, Alert 2, Alert 3, and Test Selection AlgorithmMap Video SwitcherLocation FloorCut CancelVirtual Fence Area PasteUtilities Menu Floppy a BackupRestore Screen Clear Entire FileSound Unauthorized Alarms Turn On Alarm StrobesDisplay Unauthorized Alarms Turn On Outside SoundersSecurity Alarms Silent Limit Alarms to 1 TransponderRequire Alarm Report Installer Alarms SilentMan down jitter timer ‘X’ Seconds Auto Silence Alarm In X SecondsMan Down Delay Timer X Seconds Auto Reset Comm Ports ‘X’ HoursGuard Tour Minutes System Defaults ScreenPop-up Trouble Box Contact Information New Alarm Reports Low Battery ReportNot Testing Report Weekly Maintenance Test ReportThis schedule defines the check-in times View Alarm GroupsSchedules Screen Edit Schedule TimesRemove View Alarm Groups ScreenEllipsis … AddAlarm Group State Screen Alarm Groups ScreenAlarm Group # On armedSetup Menu History Archive File a History Filter ScreenPrinter History Archive File BDatabase Backup and Restore Points, Reporting AlarmTransmitter Low Battery Database ErrorsMaster Computer Switch Login ChangesAnalyze Alarms Point TroublesPager Low BatteryTransponder Troubles Popup AC LossTamper Bus FaultsOutput Device Error Remote Key ActivationCommunications Port Monitor Comm Port Overload Pop-up Trouble and Pager DelayMap Commands Network Comm FailureReceived Transmission Map Device Type MapNot Responding Map Strobe Red LED MapPoint Out Of Service Low Battery MapOut Of Service Map Point In ServiceTotal Alarms Received On Output CommandClick On Output Command again Transponder Using Reset Transponder TroublesIncoming Retried Messages Incoming Format ErrorsSuccessful Incoming Messages Total Outgoing MessagesAC Loss Map Enable Remote KeyTamper Map Refresh DataTest Differential Alarm Min LevelAlarm Differential ByteRAM Point Info RAM EE Buss FaultReceiver Configuration Screen RAM Point StatAbort Button to Remove a Device from the Setup Mode Off Reset PointRed LED Strobe AmbientIncoming Communication Errors Enable RecStop Test and Reset Counters Transmitting PointLast Remote Access Time Total Remote Access ConnectionsTotal Wrong Access Code Attempts Reset StatusMax Man Down Messages Maximum Low Battery MessagesMaximum Test Strobe Messages Supervision MonitorsDisplay Maintenance Alarm Show Maintenance LevelsEnable Algorithm Tweaks Sound Maintenance AlarmAlarm Zone No Password TimeoutBring to Front on Alarm Bring to Front on TroubleLinear Depth Alarm Spot SizeTransponder Comm Port Setup Screen Low DepthCarrier Det Mon PowerRemote Comm Port Setup Screen No CTSPassword Remote Setup ScreenDefault Slave Computer LF OnlyVideo Switcher Control Password VerifyDisabled Video Switcher RestoreDelete Security Escort System used for remote accessEdit DialEntered into Access Password Character System ID Access PasswordVerify Password Pager Setup ScreenPrinter Menu Select Select Alarm Printer ScreenHold Printer Data FormfeedNetwork Menu Common Open File ScreenBosch Security Systems 6/12 38947D Subscriber Image Scaling % Subscriber Image File PathSubscriber Image Extension Network Socket Status ScreenAbout Menu Demo Lanyard Alarm, SubscriberWinsock Data Screen Demo Maintenance Alarm Demo Man Down Alarm, SubscriberDemo Test Subscriber 3 with low battery Demo Maintenance TestFiles Required For Security Escort Image Files Map File Generation ScalingMultiple Map Files Security Escort Pager SetupSubscriber Images Dial-up Paging Modem Setup Local Paging SetupService and Security Alarm Pager Setup Subscriber Database Advanced ScreenAlarm Area Setup Manual PagesImporting a Subscriber Database Importing a Subscriber Database Data Fields Excel Restrictions Required Order ColumnBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D