Bosch Appliances PT-400 Alarm Spot Size, Linear Depth, Low Depth, Medium Depth, Strong Depth

Page 57

Security Escort Technical Reference Manual 3.0 System Menus and Screens

EN 57

Alarm Spot Size

This setting changes the size of the yellow dot that marks the calculated location of the alarm. The settings range from 19 to 76 (half to double the default alarm dot size). It is best to set the size of the alarm spot so it represents a diameter of 15.24 m (50 ft.) on the displayed map (this is the area where the transmission of the alarm most likely took place). The Enable Algorithm Tweaks checkbox must be checked for this to be displayed.

Linear Depth

This setting controls the involvement of receivers in the alarm location calculation only when the Linear Algorithm is being used. The setting can range from zero to six (it defaults to two). When set to zero, only the receivers closer to the actual location of the alarm are considered in the location calculation. As the setting is raised, more distant receivers are included in the alarm calculation. Typically, lower settings are better than higher settings. Change this setting if there are known problems with the location using the Linear Algorithm. The Enable Algorithm Tweaks checkbox must be checked for this to display.

Low Depth

This setting controls the involvement of receivers in the alarm location calculation only when the Low Algorithm is being used. The setting can range from zero to six (it defaults to two). When set to zero only, the receivers that are closer to the actual location of the alarm are considered in the location calculation. As the setting is raised, more distant receivers are included in the alarm calculation. Typically, lower settings are better than higher settings. Change this setting if there are known problems with the location using the Low Algorithm. The Enable Algorithm Tweaks checkbox must be checked for this to display.

Medium Depth

This setting controls the involvement of receivers in the alarm location calculation only when the Medium Algorithm is being used. The setting can range from zero to six (it defaults to two). When set to zero only, the receivers that are closer to the actual location of the alarm considered in the location calculation. As the setting is raised, more distant receivers are included in the alarm calculation. Typically, lower settings are better than higher settings. Change this setting if there are known problems with the location using the Medium Algorithm. The Enable Algorithm Tweaks checkbox must be checked for this to display.

Strong Depth

This setting controls the involvement of receivers in the alarm location calculation only when the Strong Algorithm is being used. The setting can range from zero to six (it defaults to two). When set to zero only. the receivers that are closer to the actual location of the alarm are considered in the location calculation. As the setting is raised, more distant receivers are included in the alarm calculation. Typically, lower settings are better than higher settings. Change this setting if there are known problems with the location using the Strong Algorithm. The Enable Algorithm Tweaks checkbox must be checked for this to display.

3.3.18Transponder Comm Port Setup Screen

This screen connects the Comm port indexes set for each transponder in the Transponder Database to the physical Comm ports on the computer.

Figure 533: Transponder Comm Port Setup Screen

Bosch Security Systems 6/12 38947D

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Security Escort Software License Agreement Limited WarrantyYou MAY You may notRemedy Table of Contents Figures Subscriber Database Advanced TablesSystem Components Security Escort System ArchitecturePoint Transmitter Maintenance TransmitterReceiver Alert UnitTransponder Central ConsoleSoftware Overview System Operation Alarm Sequence TransmitterTransponder Scanning Receiver’s ResponseSelected in the Security Preferences Central Console Response During AlarmOperator’s Response Central Console ScreenMultiple Alarms Test Sequence TransmitterCentral Console Response Initial System Configuration Setting Up The SystemSystem Menus and Screens File MenuSubscriber Database Reports DatabasePhone Number Pager PasswordPager ID Pager GroupDisable Shorted Loop Enable Reed SwitchAlarm on Shorted Loop Alarm When Armed, Trouble When Disarmed on Shorted LoopTransponder Area Alarm GroupRequires Check-in DoneCreated, Modified, Modify Oper Database RecordTransponder ID Comm Port IndexEdit Data Insert NewKill Transponder Delete PointTrouble Tamper Text Trouble Type TextTrouble Response Text Show PointsPoint Type +, -, Bus + and BusData Entry After Selection of Receiver Point Type Alert 1, Alert 2, Alert 3, and Test Selection If the Enable algorithm tweaks field isAssigning Alert Units to Receivers AlgorithmLocation Video SwitcherMap FloorVirtual Fence Area CancelCut PasteUtilities Menu Restore Screen BackupFloppy a Clear Entire FileDisplay Unauthorized Alarms Turn On Alarm StrobesSound Unauthorized Alarms Turn On Outside SoundersRequire Alarm Report Limit Alarms to 1 TransponderSecurity Alarms Silent Installer Alarms SilentMan Down Delay Timer X Seconds Auto Silence Alarm In X SecondsMan down jitter timer ‘X’ Seconds Auto Reset Comm Ports ‘X’ HoursSystem Defaults Screen Guard Tour MinutesPop-up Trouble Box Contact Information Not Testing Report Low Battery ReportNew Alarm Reports Weekly Maintenance Test ReportSchedules Screen View Alarm GroupsThis schedule defines the check-in times Edit Schedule TimesEllipsis … View Alarm Groups ScreenRemove AddAlarm Group # Alarm Groups ScreenAlarm Group State Screen On armedSetup Menu Printer History Filter ScreenHistory Archive File a History Archive File BTransmitter Low Battery Points, Reporting AlarmDatabase Backup and Restore Database ErrorsAnalyze Alarms Login ChangesMaster Computer Switch Point TroublesTransponder Troubles Popup Low BatteryPager AC LossOutput Device Error Bus FaultsTamper Remote Key ActivationMap Commands Pop-up Trouble and Pager DelayCommunications Port Monitor Comm Port Overload Network Comm FailureNot Responding Map Device Type MapReceived Transmission Map Strobe Red LED MapOut Of Service Map Low Battery MapPoint Out Of Service Point In ServiceClick On Output Command again Transponder On Output CommandTotal Alarms Received Using Reset Transponder TroublesSuccessful Incoming Messages Incoming Format ErrorsIncoming Retried Messages Total Outgoing MessagesTamper Map Enable Remote KeyAC Loss Map Refresh DataAlarm Differential Alarm Min LevelTest Differential ByteReceiver Configuration Screen RAM EE Buss FaultRAM Point Info RAM Point StatAbort Button to Remove a Device from the Setup Mode Red LED Strobe Reset PointOff AmbientStop Test and Reset Counters Enable RecIncoming Communication Errors Transmitting PointTotal Wrong Access Code Attempts Total Remote Access ConnectionsLast Remote Access Time Reset StatusMaximum Test Strobe Messages Maximum Low Battery MessagesMax Man Down Messages Supervision MonitorsEnable Algorithm Tweaks Show Maintenance LevelsDisplay Maintenance Alarm Sound Maintenance AlarmBring to Front on Alarm No Password TimeoutAlarm Zone Bring to Front on TroubleTransponder Comm Port Setup Screen Alarm Spot SizeLinear Depth Low DepthRemote Comm Port Setup Screen Mon PowerCarrier Det No CTSDefault Slave Computer Remote Setup ScreenPassword LF OnlyDisabled Password VerifyVideo Switcher Control Video Switcher RestoreEdit Security Escort System used for remote accessDelete DialVerify Password Access PasswordEntered into Access Password Character System ID Pager Setup ScreenPrinter Menu Hold Printer Data Select Alarm Printer ScreenSelect FormfeedCommon Open File Screen Network MenuBosch Security Systems 6/12 38947D Subscriber Image Extension Subscriber Image File PathSubscriber Image Scaling % Network Socket Status ScreenDemo Lanyard Alarm, Subscriber About MenuWinsock Data Screen Demo Test Subscriber 3 with low battery Demo Man Down Alarm, SubscriberDemo Maintenance Alarm Demo Maintenance TestFiles Required For Security Escort Map File Generation Scaling Image FilesSecurity Escort Pager Setup Multiple Map FilesSubscriber Images Local Paging Setup Dial-up Paging Modem SetupSubscriber Database Advanced Screen Service and Security Alarm Pager SetupManual Pages Alarm Area SetupImporting a Subscriber Database Data Fields Excel Restrictions Required Order Column Importing a Subscriber DatabaseBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D
Top Page Image Contents