Bosch Appliances PT-400 RAM Point Info, RAM Point Stat, RAM Point Trouble, RAM EE Mstat Batt

Page 49

Security Escort Technical Reference Manual 3.0 System Menus

and Screens

EN 49

RAM Point Info

Views the RAM image of point information.

RAM Point Stat

Views the RAM image of point status.

RAM Point Trouble

Views the RAM image of point trouble.

RAM EE Mstat Batt

Views the RAM and EEPROM images of transponder status and battery condition.

RAM EE Buss Fault

Views the RAM and EEPROM images of transponder MUX bus fault condition.

RAM Counters

Views the RAM image of the process registers.

Save EE

Saves the current RAM image to the EEPROM memory on the transponder.

EE Point Info

Views the EEPROM image of point information.

EE Point Stat

Views the EEPROM image of point status.

EE Point Trouble

Views the EEPROM image of point trouble.

Bus Micro Revision

Views the bus micro revision for the connected points.

Last MUX Message

Views the last MUX bus message received.

EE counters

Views the EEPROM image of the process registers.

Clear EE

Clears the EEPROM memory on the transponder and resets the transponder.

Previous

Returns to the previous transponder in the system.

Next

Advances to the next transponder in the system.

3.3.13 Receiver Configuration Screen

Once the receiver and alert unit data for a transponder is entered into the Transponder Database, this screen is used to verify that each receiver is working and is properly addressed in the database. This setup tool identifies errors in the address switch settings of receivers and alert units, as well as data entry errors in the Transponder Database.

Figure 466: Receiver Configuration Screen

Put This Receiver In Setup Mode

This button initiates the setup process by causing both the red and green LED’s of the selected receiver illuminate.

The red and green LED flash. On the central console, the screen changes presenting an abort setup for this MUX Point button. This screen allows proceeding to the next device in the event that one receiver is not set up properly.

The next step is using a Maintenance Transmitter to transmit an alarm while standing near the receiver.

Note

Bosch Security Systems 6/12 38947D

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Security Escort Software License Agreement Limited WarrantyYou MAY You may notRemedy Table of Contents Figures Subscriber Database Advanced TablesSystem Components Security Escort System ArchitecturePoint Transmitter Maintenance TransmitterReceiver Alert UnitCentral Console TransponderSoftware Overview System Operation Alarm Sequence TransmitterTransponder Scanning Receiver’s ResponseSelected in the Security Preferences Central Console Response During AlarmOperator’s Response Central Console ScreenTest Sequence Transmitter Multiple AlarmsCentral Console Response Initial System Configuration Setting Up The SystemSystem Menus and Screens File MenuSubscriber Database Reports DatabasePhone Number Pager PasswordPager ID Pager GroupDisable Shorted Loop Enable Reed SwitchAlarm on Shorted Loop Alarm When Armed, Trouble When Disarmed on Shorted LoopTransponder Area Alarm GroupRequires Check-in DoneCreated, Modified, Modify Oper Database RecordTransponder ID Comm Port IndexEdit Data Insert NewKill Transponder Delete PointTrouble Tamper Text Trouble Type TextTrouble Response Text Show PointsPoint Type +, -, Bus + and BusData Entry After Selection of Receiver Point Type Alert 1, Alert 2, Alert 3, and Test Selection If the Enable algorithm tweaks field isAssigning Alert Units to Receivers AlgorithmLocation Video SwitcherMap FloorVirtual Fence Area CancelCut PasteUtilities Menu Restore Screen BackupFloppy a Clear Entire FileDisplay Unauthorized Alarms Turn On Alarm StrobesSound Unauthorized Alarms Turn On Outside SoundersRequire Alarm Report Limit Alarms to 1 TransponderSecurity Alarms Silent Installer Alarms SilentMan Down Delay Timer X Seconds Auto Silence Alarm In X SecondsMan down jitter timer ‘X’ Seconds Auto Reset Comm Ports ‘X’ HoursGuard Tour Minutes System Defaults ScreenPop-up Trouble Box Contact Information Not Testing Report Low Battery ReportNew Alarm Reports Weekly Maintenance Test ReportSchedules Screen View Alarm GroupsThis schedule defines the check-in times Edit Schedule TimesEllipsis … View Alarm Groups ScreenRemove AddAlarm Group # Alarm Groups ScreenAlarm Group State Screen On armedSetup Menu Printer History Filter ScreenHistory Archive File a History Archive File BTransmitter Low Battery Points, Reporting AlarmDatabase Backup and Restore Database ErrorsAnalyze Alarms Login ChangesMaster Computer Switch Point TroublesTransponder Troubles Popup Low BatteryPager AC LossOutput Device Error Bus FaultsTamper Remote Key ActivationMap Commands Pop-up Trouble and Pager DelayCommunications Port Monitor Comm Port Overload Network Comm FailureNot Responding Map Device Type MapReceived Transmission Map Strobe Red LED MapOut Of Service Map Low Battery MapPoint Out Of Service Point In ServiceClick On Output Command again Transponder On Output CommandTotal Alarms Received Using Reset Transponder TroublesSuccessful Incoming Messages Incoming Format ErrorsIncoming Retried Messages Total Outgoing MessagesTamper Map Enable Remote KeyAC Loss Map Refresh DataAlarm Differential Alarm Min LevelTest Differential ByteReceiver Configuration Screen RAM EE Buss FaultRAM Point Info RAM Point StatAbort Button to Remove a Device from the Setup Mode Red LED Strobe Reset PointOff AmbientStop Test and Reset Counters Enable RecIncoming Communication Errors Transmitting PointTotal Wrong Access Code Attempts Total Remote Access ConnectionsLast Remote Access Time Reset StatusMaximum Test Strobe Messages Maximum Low Battery MessagesMax Man Down Messages Supervision MonitorsEnable Algorithm Tweaks Show Maintenance LevelsDisplay Maintenance Alarm Sound Maintenance AlarmBring to Front on Alarm No Password TimeoutAlarm Zone Bring to Front on TroubleTransponder Comm Port Setup Screen Alarm Spot SizeLinear Depth Low DepthRemote Comm Port Setup Screen Mon PowerCarrier Det No CTSDefault Slave Computer Remote Setup ScreenPassword LF OnlyDisabled Password VerifyVideo Switcher Control Video Switcher RestoreEdit Security Escort System used for remote accessDelete DialVerify Password Access PasswordEntered into Access Password Character System ID Pager Setup ScreenPrinter Menu Hold Printer Data Select Alarm Printer ScreenSelect FormfeedCommon Open File Screen Network MenuBosch Security Systems 6/12 38947D Subscriber Image Extension Subscriber Image File PathSubscriber Image Scaling % Network Socket Status ScreenAbout Menu Demo Lanyard Alarm, SubscriberWinsock Data Screen Demo Test Subscriber 3 with low battery Demo Man Down Alarm, SubscriberDemo Maintenance Alarm Demo Maintenance TestFiles Required For Security Escort Map File Generation Scaling Image FilesMultiple Map Files Security Escort Pager SetupSubscriber Images Local Paging Setup Dial-up Paging Modem SetupSubscriber Database Advanced Screen Service and Security Alarm Pager SetupManual Pages Alarm Area SetupImporting a Subscriber Database Data Fields Excel Restrictions Required Order Column Importing a Subscriber DatabaseBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D
Top Page Image Contents