Bosch Appliances PT-400 Low Battery Map, ’m OK Check, I’m OK Release Control Buttons, Horn Siren

Page 44

Security Escort Technical Reference Manual 3.0 System Menus and Screens

EN 44

Spare

This is a future option. Not implemented at this time.

Low Battery Map

Requests a map of all the alert units that are currently reporting a Low Battery to the system. The Low Battery Map button displays a map with “1” in the locations corresponding to points that are reporting Low Battery.

I’m OK Check, I’m OK Release Control

Buttons

These buttons are used to diagnose and correct communications problems between the central console and the transponder. The system software requires that each transponder send a message to the central console periodically if no other communications have taken place. These messages are called I’m OK messages. If for some reason the communications link between the central console and the transponder fails, the transponder recognizes the fact when its I’m OK transmissions are not acknowledged by the central console. When the transponder has retried transmitting an I’m OK message or any other message six times without acknowledgment, it assumes control of the outputs (LED’s, horns, strobes, and sirens) on devices connected to it and modifies the message to indicate that it is still OK and has taken control. These messages are transmitted once per minute until communications are reestablished.

The I’m OK Check button requests that the transponder send an I’m OK message. This is used to determine if a transponder has taken control of its outputs. The I’m OK Release Control button generates a command to the transponder to release control back to the central console. Normally, the central console automatically generates a Release Control message upon the re- establishment of communications following a failure.

Out Of Service Map

The Out Of Service Map shows those points (receivers or alert units) that are currently out of service. Points may be taken out of service and returned to service by selecting the point using MUX Bus Point Screen in the bottom right corner of the screen and clicking the Point Out Of Service or Point In Service button. Points can be selected by typing in the point number or by using the [+] and [-] buttons, or the [?] button.

Point Out Of Service

Clicking this button takes the currently selected point out-of- service. That point no longer responds to the system, as if it was disconnected. Use this function with caution.

Point In Service

Clicking this button restores the currently selected point to an in- service condition. That point returns to normal function.

Transponder Outputs

Requests the current state of the siren and strobe outputs on the transponder.

Reset Transponder

Clicking this button resets the transponder as if it was just powered up. Any test or alarm processing that was in progress at the time is lost.

Horn - Siren

If this checkbox is checked, the horn output of a receiver or the siren output of an alert unit is turned on if On Output Command is clicked, or off if Off is clicked. If this checkbox is not checked, the state of this output is not changed.

Green LED

If this checkbox is checked, the green LED output of a receiver or the spare output of an alert unit is turned on if On Output Command is clicked, or off if Off is clicked. If this checkbox is not checked, the state of this output is not change.

Strobe – Red LED

If this checkbox is checked, the red LED output of a receiver or the strobe output of an alert unit is turned on if On Output Command is clicked, or off if Off is clicked. If this checkbox is not checked, the state of this output is not changed.

Bosch Security Systems 6/12 38947D

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Security Escort Limited Warranty Software License AgreementYou MAY You may notRemedy Table of Contents Figures Tables Subscriber Database AdvancedSecurity Escort System Architecture System ComponentsMaintenance Transmitter Point TransmitterReceiver Alert UnitSoftware Overview TransponderCentral Console Alarm Sequence Transmitter System OperationTransponder Scanning Receiver’s ResponseCentral Console Response During Alarm Selected in the Security PreferencesOperator’s Response Central Console ScreenCentral Console Response Multiple AlarmsTest Sequence Transmitter Setting Up The System Initial System ConfigurationSystem Menus and Screens File MenuReports Database Subscriber DatabasePager Password Phone NumberPager ID Pager GroupEnable Reed Switch Disable Shorted LoopAlarm on Shorted Loop Alarm When Armed, Trouble When Disarmed on Shorted LoopAlarm Group Transponder AreaRequires Check-in DoneDatabase Record Created, Modified, Modify OperTransponder ID Comm Port IndexInsert New Edit DataKill Transponder Delete PointTrouble Type Text Trouble Tamper TextTrouble Response Text Show Points+, -, Bus + and Bus Point TypeData Entry After Selection of Receiver Point Type If the Enable algorithm tweaks field is Alert 1, Alert 2, Alert 3, and Test SelectionAssigning Alert Units to Receivers AlgorithmVideo Switcher LocationMap FloorCancel Virtual Fence AreaCut PasteUtilities Menu Backup Restore ScreenFloppy a Clear Entire FileTurn On Alarm Strobes Display Unauthorized AlarmsSound Unauthorized Alarms Turn On Outside SoundersLimit Alarms to 1 Transponder Require Alarm ReportSecurity Alarms Silent Installer Alarms SilentAuto Silence Alarm In X Seconds Man Down Delay Timer X SecondsMan down jitter timer ‘X’ Seconds Auto Reset Comm Ports ‘X’ HoursPop-up Trouble Box Contact Information System Defaults ScreenGuard Tour Minutes Low Battery Report Not Testing ReportNew Alarm Reports Weekly Maintenance Test ReportView Alarm Groups Schedules ScreenThis schedule defines the check-in times Edit Schedule TimesView Alarm Groups Screen Ellipsis …Remove AddAlarm Groups Screen Alarm Group #Alarm Group State Screen On armedSetup Menu History Filter Screen PrinterHistory Archive File a History Archive File BPoints, Reporting Alarm Transmitter Low BatteryDatabase Backup and Restore Database ErrorsLogin Changes Analyze AlarmsMaster Computer Switch Point TroublesLow Battery Transponder Troubles PopupPager AC LossBus Faults Output Device ErrorTamper Remote Key ActivationPop-up Trouble and Pager Delay Map CommandsCommunications Port Monitor Comm Port Overload Network Comm FailureDevice Type Map Not Responding MapReceived Transmission Map Strobe Red LED MapLow Battery Map Out Of Service MapPoint Out Of Service Point In ServiceOn Output Command Click On Output Command again TransponderTotal Alarms Received Using Reset Transponder TroublesIncoming Format Errors Successful Incoming MessagesIncoming Retried Messages Total Outgoing MessagesEnable Remote Key Tamper MapAC Loss Map Refresh DataAlarm Min Level Alarm DifferentialTest Differential ByteRAM EE Buss Fault Receiver Configuration ScreenRAM Point Info RAM Point StatAbort Button to Remove a Device from the Setup Mode Reset Point Red LED StrobeOff AmbientEnable Rec Stop Test and Reset CountersIncoming Communication Errors Transmitting PointTotal Remote Access Connections Total Wrong Access Code AttemptsLast Remote Access Time Reset StatusMaximum Low Battery Messages Maximum Test Strobe MessagesMax Man Down Messages Supervision MonitorsShow Maintenance Levels Enable Algorithm TweaksDisplay Maintenance Alarm Sound Maintenance AlarmNo Password Timeout Bring to Front on AlarmAlarm Zone Bring to Front on TroubleAlarm Spot Size Transponder Comm Port Setup ScreenLinear Depth Low DepthMon Power Remote Comm Port Setup ScreenCarrier Det No CTSRemote Setup Screen Default Slave ComputerPassword LF OnlyPassword Verify DisabledVideo Switcher Control Video Switcher RestoreSecurity Escort System used for remote access EditDelete DialAccess Password Verify PasswordEntered into Access Password Character System ID Pager Setup ScreenPrinter Menu Select Alarm Printer Screen Hold Printer DataSelect FormfeedNetwork Menu Common Open File ScreenBosch Security Systems 6/12 38947D Subscriber Image File Path Subscriber Image ExtensionSubscriber Image Scaling % Network Socket Status ScreenWinsock Data Screen Demo Lanyard Alarm, SubscriberAbout Menu Demo Man Down Alarm, Subscriber Demo Test Subscriber 3 with low batteryDemo Maintenance Alarm Demo Maintenance TestFiles Required For Security Escort Image Files Map File Generation ScalingSubscriber Images Security Escort Pager SetupMultiple Map Files Dial-up Paging Modem Setup Local Paging SetupService and Security Alarm Pager Setup Subscriber Database Advanced ScreenAlarm Area Setup Manual PagesImporting a Subscriber Database Importing a Subscriber Database Data Fields Excel Restrictions Required Order ColumnBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D
Top Page Image Contents