Bosch Appliances PT-400 manual Subscriber Image File Path, Subscriber Image Extension

Page 67

Security Escort Technical Reference Manual 3.0 System Menus

EN 67

and Screens

 

Note:

With version 2.04 of the software it is possible to use UNC path names rather than mapping drive letters. Therefore, the path to the master computer’s database is \\SLAVE\C\ESCORT.

Local Escort Path: The path on this workstation the Security Escort was installed in. Typically, it is C:\ESCORT.

Backup/Restore to Disk Cartridge Path

When backing up or restoring the databases to a disk cartridge use this path.

Subscriber Image File Path

The Security Escort System software can display an image for each subscriber on the alarm screen. This parameter tells the software the path to where the image files are stored. The default is C:\ESCORT\IMAGES.

Subscriber Image Extension

The subscriber images can be in JPEG or Windows Bitmap format. All images in a system must be in the same format. For the JPEG format, enter the Windows extension JPG. For the Bitmap format, enter the Windows extension BMP.

Subscriber Image Scaling %

When the display is set to 640 by 480 pixels and subscriber images are being displayed, this parameter controls the image size. This value can range from 10% to 100% and should be adjusted while viewing alarms to get the desired image size. When the display is set to 800 by 600 or larger (recommended), this parameter has no effect.

3.5.2 Network Socket Status Screen

This screen shows diagnostic information for the selected TCP/IP socket.

Figure 677: Current Network Socket Status Screen

Successful Incoming Messages

This value is the number of messages the system successfully received on this socket.

Incoming Communication Errors

This value is the number of messages the system detected errors in, on this socket. If displayed in yellow, this value is more than 1.5% of the Successful Incoming Messages.

Incoming Retried Messages

This value is the number of successful receptions that indicated that the sending application retried. If displayed in yellow, this value is more than 1.5% of the Successful Incoming Messages.

Total Outgoing Messages

This value is the total number of outgoing messages that were sent on this socket.

Outgoing Retried Messages

This value is number of outgoing messages that must be retried because the receiving application did not acknowledge them. If displayed in yellow, this value is more than 1.5% of the Total Outgoing Messages.

Receive Buffer Max

This value is the maximum number of bytes that were received on this serial port, but not yet processed by the system. If displayed in yellow, more than 50% of the queue was in use.

Bosch Security Systems 6/12 38947D

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Security Escort You may not Limited WarrantySoftware License Agreement You MAYRemedy Table of Contents Figures Subscriber Database Advanced TablesSystem Components Security Escort System ArchitectureAlert Unit Maintenance TransmitterPoint Transmitter ReceiverCentral Console TransponderSoftware Overview Receiver’s Response Alarm Sequence TransmitterSystem Operation Transponder ScanningCentral Console Screen Central Console Response During AlarmSelected in the Security Preferences Operator’s ResponseTest Sequence Transmitter Multiple AlarmsCentral Console Response File Menu Setting Up The SystemInitial System Configuration System Menus and ScreensSubscriber Database Reports DatabasePager Group Pager PasswordPhone Number Pager IDAlarm When Armed, Trouble When Disarmed on Shorted Loop Enable Reed SwitchDisable Shorted Loop Alarm on Shorted LoopDone Alarm GroupTransponder Area Requires Check-inComm Port Index Database RecordCreated, Modified, Modify Oper Transponder IDDelete Point Insert NewEdit Data Kill TransponderShow Points Trouble Type TextTrouble Tamper Text Trouble Response TextPoint Type +, -, Bus + and BusData Entry After Selection of Receiver Point Type Algorithm If the Enable algorithm tweaks field isAlert 1, Alert 2, Alert 3, and Test Selection Assigning Alert Units to ReceiversFloor Video SwitcherLocation MapPaste CancelVirtual Fence Area CutUtilities Menu Clear Entire File BackupRestore Screen Floppy aTurn On Outside Sounders Turn On Alarm StrobesDisplay Unauthorized Alarms Sound Unauthorized AlarmsInstaller Alarms Silent Limit Alarms to 1 TransponderRequire Alarm Report Security Alarms SilentAuto Reset Comm Ports ‘X’ Hours Auto Silence Alarm In X SecondsMan Down Delay Timer X Seconds Man down jitter timer ‘X’ SecondsGuard Tour Minutes System Defaults ScreenPop-up Trouble Box Contact Information Weekly Maintenance Test Report Low Battery ReportNot Testing Report New Alarm ReportsEdit Schedule Times View Alarm GroupsSchedules Screen This schedule defines the check-in timesAdd View Alarm Groups ScreenEllipsis … RemoveOn armed Alarm Groups ScreenAlarm Group # Alarm Group State ScreenSetup Menu History Archive File B History Filter ScreenPrinter History Archive File aDatabase Errors Points, Reporting AlarmTransmitter Low Battery Database Backup and RestorePoint Troubles Login ChangesAnalyze Alarms Master Computer SwitchAC Loss Low BatteryTransponder Troubles Popup PagerRemote Key Activation Bus FaultsOutput Device Error TamperNetwork Comm Failure Pop-up Trouble and Pager DelayMap Commands Communications Port Monitor Comm Port OverloadStrobe Red LED Map Device Type MapNot Responding Map Received Transmission MapPoint In Service Low Battery MapOut Of Service Map Point Out Of ServiceUsing Reset Transponder Troubles On Output CommandClick On Output Command again Transponder Total Alarms ReceivedTotal Outgoing Messages Incoming Format ErrorsSuccessful Incoming Messages Incoming Retried MessagesRefresh Data Enable Remote KeyTamper Map AC Loss MapByte Alarm Min LevelAlarm Differential Test DifferentialRAM Point Stat RAM EE Buss FaultReceiver Configuration Screen RAM Point InfoAbort Button to Remove a Device from the Setup Mode Ambient Reset PointRed LED Strobe OffTransmitting Point Enable RecStop Test and Reset Counters Incoming Communication ErrorsReset Status Total Remote Access ConnectionsTotal Wrong Access Code Attempts Last Remote Access TimeSupervision Monitors Maximum Low Battery MessagesMaximum Test Strobe Messages Max Man Down MessagesSound Maintenance Alarm Show Maintenance LevelsEnable Algorithm Tweaks Display Maintenance AlarmBring to Front on Trouble No Password TimeoutBring to Front on Alarm Alarm ZoneLow Depth Alarm Spot SizeTransponder Comm Port Setup Screen Linear DepthNo CTS Mon PowerRemote Comm Port Setup Screen Carrier DetLF Only Remote Setup ScreenDefault Slave Computer PasswordVideo Switcher Restore Password VerifyDisabled Video Switcher ControlDial Security Escort System used for remote accessEdit DeletePager Setup Screen Access PasswordVerify Password Entered into Access Password Character System IDPrinter Menu Formfeed Select Alarm Printer ScreenHold Printer Data SelectCommon Open File Screen Network MenuBosch Security Systems 6/12 38947D Network Socket Status Screen Subscriber Image File PathSubscriber Image Extension Subscriber Image Scaling %About Menu Demo Lanyard Alarm, SubscriberWinsock Data Screen Demo Maintenance Test Demo Man Down Alarm, SubscriberDemo Test Subscriber 3 with low battery Demo Maintenance AlarmFiles Required For Security Escort Map File Generation Scaling Image FilesMultiple Map Files Security Escort Pager SetupSubscriber Images Local Paging Setup Dial-up Paging Modem SetupSubscriber Database Advanced Screen Service and Security Alarm Pager SetupManual Pages Alarm Area SetupImporting a Subscriber Database Data Fields Excel Restrictions Required Order Column Importing a Subscriber DatabaseBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D
Top Page Image Contents