Bosch Appliances PT-400 manual Transponder Area, Alarm Group, Requires Check-in, Done

Page 17

Security Escort Technical Reference Manual 3.0 System Menus and Screens

EN 17

Transponder Area

Wandering Alarm - Create a protected area by placing a virtual monitor fence around an area of the main map. These areas are defined in the transponder database. If this transmitter is constrained to remain within one of these defined areas, first select the defining transponder in the Transponder Name field. Then select the desired area from this dropdown list of the transponder’s area names.

For the wandering alarm to work, the supervision period must also be programmed for this transmitter.

Specific transmitters are marked in the Subscriber Database to be constrained within a specific fenced area defined by this option. If the transmitters leave their defined area, the system reports this as a wandering alarm and continues to monitor and track the location of the transmitter until the alarm is canceled from the screen in the normal way. However, these tracking updates can only occur every supervision transmission period (not on an accelerated rate like a tracking alarm).

The Security Escort System computes the location of the transmitters when they broadcast automatic supervision transmissions periodically.

Because of the basic location accuracy and the floor-to-floor accuracy of the system, there is a potential for some false alarms. If false alarms are a problem, check the Filter Virtual Fence checkbox in the Edit Security Preferences Screen. If you do this, two successive location calculations indicate the transmitter moved outside the protected area before an alarm was generated. The downside of this is a delay in the reporting of a wandering alarm of one extra transmitter supervision period.

Alarm Group

This is the alarm group that controls the arm/disarm status of this transmitter. Select the desired alarm group from the dropdown list. This alarm group must be armed for this transmitter to cause an alarm, which is displayed. If no alarm group is assigned, the transmitter is always armed.

Requires Check-in

When this checkbox is checked, this transmitter activates once each day during the check-in schedule time. At the end of the check-in period, if the subscriber fails to check-in, a Failed to Check-in Report is generated and presented to the operator. This report contains all of the people who failed to check-in with their first address line and phone number. All subscribers in the report must be checked on to make sure they are not in need of assistance, as this may be a life- threatening situation. A printed report may be generated.

If the transmitter is not a point type, the transmitter can generate alarms and therefore a test transmission is used for the check-in.

If the transmitter is a point type, any non-trouble transmission serves as a check-in.

One of the ten schedules must be selected as the check-in schedule to define the check-in period.

Done

Click this button when all changes are complete to return the main Subscriber Database Edit Screen.

3.1.6 Transponder Database

The Transponder Database is established at system set-up and contains all necessary configuration data for each transponder, receiver, and alert unit. It describes the basic structure of the installation, including all device names, locations, types, multiplex addresses, and so on. This information is used by the central console to generate alarm and test displays on the central console and in determining which alert units are activated.

Figure 8: Find Transponder’s

Bosch Security Systems 6/12 38947D

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Security Escort Software License Agreement Limited WarrantyYou MAY You may notRemedy Table of Contents Figures Subscriber Database Advanced TablesSystem Components Security Escort System ArchitecturePoint Transmitter Maintenance TransmitterReceiver Alert UnitSoftware Overview TransponderCentral Console System Operation Alarm Sequence TransmitterTransponder Scanning Receiver’s ResponseSelected in the Security Preferences Central Console Response During AlarmOperator’s Response Central Console ScreenCentral Console Response Multiple AlarmsTest Sequence Transmitter Initial System Configuration Setting Up The SystemSystem Menus and Screens File MenuSubscriber Database Reports DatabasePhone Number Pager PasswordPager ID Pager GroupDisable Shorted Loop Enable Reed SwitchAlarm on Shorted Loop Alarm When Armed, Trouble When Disarmed on Shorted LoopTransponder Area Alarm GroupRequires Check-in DoneCreated, Modified, Modify Oper Database RecordTransponder ID Comm Port IndexEdit Data Insert NewKill Transponder Delete PointTrouble Tamper Text Trouble Type TextTrouble Response Text Show PointsPoint Type +, -, Bus + and BusData Entry After Selection of Receiver Point Type Alert 1, Alert 2, Alert 3, and Test Selection If the Enable algorithm tweaks field isAssigning Alert Units to Receivers AlgorithmLocation Video SwitcherMap FloorVirtual Fence Area CancelCut PasteUtilities Menu Restore Screen BackupFloppy a Clear Entire FileDisplay Unauthorized Alarms Turn On Alarm StrobesSound Unauthorized Alarms Turn On Outside SoundersRequire Alarm Report Limit Alarms to 1 TransponderSecurity Alarms Silent Installer Alarms SilentMan Down Delay Timer X Seconds Auto Silence Alarm In X SecondsMan down jitter timer ‘X’ Seconds Auto Reset Comm Ports ‘X’ HoursPop-up Trouble Box Contact Information System Defaults ScreenGuard Tour Minutes Not Testing Report Low Battery ReportNew Alarm Reports Weekly Maintenance Test ReportSchedules Screen View Alarm GroupsThis schedule defines the check-in times Edit Schedule TimesEllipsis … View Alarm Groups ScreenRemove AddAlarm Group # Alarm Groups ScreenAlarm Group State Screen On armedSetup Menu Printer History Filter ScreenHistory Archive File a History Archive File BTransmitter Low Battery Points, Reporting AlarmDatabase Backup and Restore Database ErrorsAnalyze Alarms Login ChangesMaster Computer Switch Point TroublesTransponder Troubles Popup Low BatteryPager AC LossOutput Device Error Bus FaultsTamper Remote Key ActivationMap Commands Pop-up Trouble and Pager DelayCommunications Port Monitor Comm Port Overload Network Comm FailureNot Responding Map Device Type MapReceived Transmission Map Strobe Red LED MapOut Of Service Map Low Battery MapPoint Out Of Service Point In ServiceClick On Output Command again Transponder On Output CommandTotal Alarms Received Using Reset Transponder TroublesSuccessful Incoming Messages Incoming Format ErrorsIncoming Retried Messages Total Outgoing MessagesTamper Map Enable Remote KeyAC Loss Map Refresh DataAlarm Differential Alarm Min LevelTest Differential ByteReceiver Configuration Screen RAM EE Buss FaultRAM Point Info RAM Point StatAbort Button to Remove a Device from the Setup Mode Red LED Strobe Reset PointOff AmbientStop Test and Reset Counters Enable RecIncoming Communication Errors Transmitting PointTotal Wrong Access Code Attempts Total Remote Access ConnectionsLast Remote Access Time Reset StatusMaximum Test Strobe Messages Maximum Low Battery MessagesMax Man Down Messages Supervision MonitorsEnable Algorithm Tweaks Show Maintenance LevelsDisplay Maintenance Alarm Sound Maintenance AlarmBring to Front on Alarm No Password TimeoutAlarm Zone Bring to Front on TroubleTransponder Comm Port Setup Screen Alarm Spot SizeLinear Depth Low DepthRemote Comm Port Setup Screen Mon PowerCarrier Det No CTSDefault Slave Computer Remote Setup ScreenPassword LF OnlyDisabled Password VerifyVideo Switcher Control Video Switcher RestoreEdit Security Escort System used for remote accessDelete DialVerify Password Access PasswordEntered into Access Password Character System ID Pager Setup ScreenPrinter Menu Hold Printer Data Select Alarm Printer ScreenSelect FormfeedCommon Open File Screen Network MenuBosch Security Systems 6/12 38947D Subscriber Image Extension Subscriber Image File PathSubscriber Image Scaling % Network Socket Status ScreenWinsock Data Screen Demo Lanyard Alarm, SubscriberAbout Menu Demo Test Subscriber 3 with low battery Demo Man Down Alarm, SubscriberDemo Maintenance Alarm Demo Maintenance TestFiles Required For Security Escort Map File Generation Scaling Image FilesSubscriber Images Security Escort Pager SetupMultiple Map Files Local Paging Setup Dial-up Paging Modem SetupSubscriber Database Advanced Screen Service and Security Alarm Pager SetupManual Pages Alarm Area SetupImporting a Subscriber Database Data Fields Excel Restrictions Required Order Column Importing a Subscriber DatabaseBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D
Top Page Image Contents