Bosch Appliances PT-400 Transmitting Point, Total Transmissions, Missed all Receivers, Enable Rec

Page 52

Security Escort Technical Reference Manual 3.0 System Menus

and Screens

EN 52

Transponder

Select the transponder for the transmitting point and each receiving point. They can be on the same or different transponders.

Transmitting Point

Select the point (receiver) on the selected transponder to generate the transmissions.

Total Transmissions

The total number of times the designated receiver transmitted the test message.

Missed all Receivers

The total number of times that the test transmission, was not heard by any of the designated receivers.

Enable Rec

This box must be checked for this receiver to monitor the test transmissions.

Point

Select the point (receiver) on this transponder to monitor the test transmissions.

Hits

The number of times this receiver successfully heard the test transmission.

Misses

The number of times this receiver failed to hear the test transmission.

Highest

The left-hand box displays the highest receive level at which the test transmission was heard. The right-hand box displays the greatest number of packets heard from a single test transmission.

Average

The left-hand box displays the average receive level at which the test transmission was heard. The right-hand box displays the average number of packets heard from a single test transmission.

Lowest

The left-hand box displays the lowest receive level at which the test transmission was heard. The right-hand box displays the least number of packets heard from a single test transmission.

Run Test

The test only runs when this box is checked. To stop the test and retain the test values, uncheck this box.

Spacing

This slows the test by forcing this number of seconds between test transmissions. Normally, this setting is left at the default of 0.

Stop Test and Reset Counters

Clicking this button stops the test and resets all values.

Close Screen, Does Not Stop Test

Clicking this button closes this screen but does not stop the test from running. Reopening the screen displays the current progress of the test. The test should not be left running unless there is a specific need, as it generates both RF and system traffic.

3.3.15Network Status Screen

This screen shows the status of communications on the network, modem, and system serial ports.

Figure 500: Network Status Screen

Successful Incoming Messages

This value is the number of messages that the system successfully received on this communications port.

Incoming Communication Errors

This value is the number of messages that the system detected errors in, on this communications port. If displayed in yellow, this value is more than 1.5% of the Successful Incoming Messages.

Bosch Security Systems 6/12 38947D

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Security Escort Limited Warranty Software License AgreementYou MAY You may notRemedy Table of Contents Figures Tables Subscriber Database AdvancedSecurity Escort System Architecture System ComponentsMaintenance Transmitter Point TransmitterReceiver Alert UnitCentral Console TransponderSoftware Overview Alarm Sequence Transmitter System OperationTransponder Scanning Receiver’s ResponseCentral Console Response During Alarm Selected in the Security PreferencesOperator’s Response Central Console ScreenTest Sequence Transmitter Multiple AlarmsCentral Console Response Setting Up The System Initial System ConfigurationSystem Menus and Screens File MenuReports Database Subscriber DatabasePager Password Phone NumberPager ID Pager GroupEnable Reed Switch Disable Shorted LoopAlarm on Shorted Loop Alarm When Armed, Trouble When Disarmed on Shorted LoopAlarm Group Transponder AreaRequires Check-in DoneDatabase Record Created, Modified, Modify OperTransponder ID Comm Port IndexInsert New Edit DataKill Transponder Delete PointTrouble Type Text Trouble Tamper TextTrouble Response Text Show Points+, -, Bus + and Bus Point TypeData Entry After Selection of Receiver Point Type If the Enable algorithm tweaks field is Alert 1, Alert 2, Alert 3, and Test SelectionAssigning Alert Units to Receivers AlgorithmVideo Switcher LocationMap FloorCancel Virtual Fence AreaCut PasteUtilities Menu Backup Restore ScreenFloppy a Clear Entire FileTurn On Alarm Strobes Display Unauthorized AlarmsSound Unauthorized Alarms Turn On Outside SoundersLimit Alarms to 1 Transponder Require Alarm ReportSecurity Alarms Silent Installer Alarms SilentAuto Silence Alarm In X Seconds Man Down Delay Timer X SecondsMan down jitter timer ‘X’ Seconds Auto Reset Comm Ports ‘X’ HoursGuard Tour Minutes System Defaults ScreenPop-up Trouble Box Contact Information Low Battery Report Not Testing ReportNew Alarm Reports Weekly Maintenance Test ReportView Alarm Groups Schedules ScreenThis schedule defines the check-in times Edit Schedule TimesView Alarm Groups Screen Ellipsis …Remove AddAlarm Groups Screen Alarm Group #Alarm Group State Screen On armedSetup Menu History Filter Screen PrinterHistory Archive File a History Archive File BPoints, Reporting Alarm Transmitter Low BatteryDatabase Backup and Restore Database ErrorsLogin Changes Analyze AlarmsMaster Computer Switch Point TroublesLow Battery Transponder Troubles PopupPager AC LossBus Faults Output Device ErrorTamper Remote Key ActivationPop-up Trouble and Pager Delay Map CommandsCommunications Port Monitor Comm Port Overload Network Comm FailureDevice Type Map Not Responding MapReceived Transmission Map Strobe Red LED MapLow Battery Map Out Of Service MapPoint Out Of Service Point In ServiceOn Output Command Click On Output Command again TransponderTotal Alarms Received Using Reset Transponder TroublesIncoming Format Errors Successful Incoming MessagesIncoming Retried Messages Total Outgoing MessagesEnable Remote Key Tamper MapAC Loss Map Refresh DataAlarm Min Level Alarm DifferentialTest Differential Byte RAM EE Buss Fault Receiver Configuration Screen RAM Point Info RAM Point StatAbort Button to Remove a Device from the Setup Mode Reset Point Red LED StrobeOff AmbientEnable Rec Stop Test and Reset CountersIncoming Communication Errors Transmitting PointTotal Remote Access Connections Total Wrong Access Code AttemptsLast Remote Access Time Reset StatusMaximum Low Battery Messages Maximum Test Strobe MessagesMax Man Down Messages Supervision MonitorsShow Maintenance Levels Enable Algorithm TweaksDisplay Maintenance Alarm Sound Maintenance AlarmNo Password Timeout Bring to Front on AlarmAlarm Zone Bring to Front on TroubleAlarm Spot Size Transponder Comm Port Setup ScreenLinear Depth Low DepthMon Power Remote Comm Port Setup ScreenCarrier Det No CTSRemote Setup Screen Default Slave ComputerPassword LF OnlyPassword Verify DisabledVideo Switcher Control Video Switcher RestoreSecurity Escort System used for remote access EditDelete DialAccess Password Verify PasswordEntered into Access Password Character System ID Pager Setup ScreenPrinter Menu Select Alarm Printer Screen Hold Printer DataSelect FormfeedNetwork Menu Common Open File ScreenBosch Security Systems 6/12 38947D Subscriber Image File Path Subscriber Image ExtensionSubscriber Image Scaling % Network Socket Status ScreenAbout Menu Demo Lanyard Alarm, SubscriberWinsock Data Screen Demo Man Down Alarm, Subscriber Demo Test Subscriber 3 with low batteryDemo Maintenance Alarm Demo Maintenance TestFiles Required For Security Escort Image Files Map File Generation ScalingMultiple Map Files Security Escort Pager SetupSubscriber Images Dial-up Paging Modem Setup Local Paging SetupService and Security Alarm Pager Setup Subscriber Database Advanced ScreenAlarm Area Setup Manual PagesImporting a Subscriber Database Importing a Subscriber Database Data Fields Excel Restrictions Required Order ColumnBosch Security Systems 6/12 38947D Autobackup to the slave database CR/LF Idle Time Multiplex Point Refresh Data 47, 53, 54 System Preferences Security Escort Technical Reference Manual Index Bosch Security Systems 38947D
Top Page Image Contents