Bosch Appliances 500 user manual Canting in progress

Page 16

16 en Mounting	MIC Series 500 Camera

3.Grasp the lower camera body beneath the pan body joint and then carefully twist the upper camera body clockwise until the camera body has rotated 180° around, canting the top part of the camera to the 45° angle. Ensure that the securing bolt holes are aligned.

Figure 4.6 Canting in progress

4.Carefully replace and tighten the pan body securing the supplied (MIC-DCA, MIC-SCA, MIC-WMB) bolts. Ensure not to damage the paint work on the camera.

Figure 4.7 Camera canted

5.The MIC 500 Series Camera is now ready to be installed and configured.

NOTICE!

Installation should be made by qualified service personnel and conform to the National Electrical Code and applicable local codes. Ensure a strong safety chain is used to secure the MIC 500 Series Camera to prevent any danger of dropping the product during installation.

The following graphic shows the various positions of the MIC 500 Series Camera. See the table below for the descriptions.

Figure 4.8 MIC 500 Series Cameras (From left to right: Canted full frontal view; Upright full frontal view; Upright side view; Canted side view)

F.01U.173.601 2.0 2010.11

User’s Manual

Bosch Security Systems, Inc.

Image 16

Contents MIC Series 500 Camera Page Table of Contents Appendices 1Safety Important Safety InstructionsSafety Precautions Important Notices Coax groundingFCC & Ices Information A. and Canadian Models OnlyInformations FCC ET Ices DisclaimerCopyright TrademarksCustomer Support and Service Parts List UnpackingAdditional Tools Required Quantity Part1Features 2Power3Description 3Video4Mounting Part DescriptionAdjusting the MIC 500 Series Camera Pan body fixing screwsCanting in progress Adjusting the Rain Shield for Inverted Operation Remove screwsMounting the MIC 500 Series Camera Lightning Protection Earthing the MIC 500 Series CameraElectrical Connections 13 Composite cable before connection Red Navigating the Menus Menu Item Description Exit1MIC Setups Menu Available only via the menu see .1.1 Config Mode,Setting Options Default ON/OFFTour ON/OFF OSDActivate Feature Menu 3Preset Tour MenuConfig Mode Image Flip Pan Reverse Tilt Reverse PrivacyCreate/Modify Tour Tour Setting ValueRandom Tours Tour Point Preset Position Dwell Time Pattern Tour MenuRecording a Pattern Tour Preview TourLearn Preset 5Presets MenuGoto Preset 6Communications Menu Manual ControlAdvanced Setups Menu Menu Item Description Options DefaultWipe Mode INTWipes Hour AutoFactory Defaults Re-map Pelco Aux Pelco D and P Protocols onlyAlarms Menu Relay 2 Status SET with Alarm Normally ClosedAux Number Function Menu Item Description OptionsAlarm Relays and Re-arm Time 9Sony Set MenuRelay Relay Activation Relay StateMapping to a MIC 500 Series Camera Function Exposure Shutter Priority 4 SET ShutterNumber Function ValueSetting Values Available Setting OptionsOn / OFF Aperture Reset / Plus 1 / Minus Aperture Set Low Lux Brightness Value Iris Setting Gain Setting Exposure Comp Value Iris Setting Gain Setting Focus Pos Focus DistanceIris Value Iris Setting Gain Value Gain SettingCaptions Menu Shutter Value Shutter Speed10.1 Default Caption 10.2 Preset Captions10.4Setting Captions 10.3 Sector CaptionsBlank Single Blank Save Single Save Sector /4 Sector Caption11.2Setting the Privacy Zones Privacy Menu11.1 Mask / Clear Whole Menu Item OptionsPot Test Menu 13MIC Information MenuGoto Preset Mapping Sony SET Current MIC Settings Auto Alarm OFF Multi Alarm Alarm RearmWipe Mode Normal WASH-WIPE OFF Control Card Data Serial Issue 8A14Set User Access Menu 13.1 MIC Information MenusSetting Default Value 14.1 Factory DefaultsOSD OFF Help Menu 16Self DiagnosisSupport USA EmeaAppendices MIC 500 Series Aux ControlsPreset Number Learn and Go to Preset Function MIC 500 Preset ControlsPreset Number Go To / Shot Preset Function Preset Number Learn Preset Function MIC 500 Model Numbers and Descriptions Model No DescriptionPage Bosch Security Systems, Inc

Related manuals

Manual 8 pages 56.48 Kb