MIC Series 500 CameraNavigating the Menus en 33
Menu Item | Description | Options | Default |
|
|
|
|
CLEAR SOFT | Clears any Soft stops that have been applied. | RIGHT TO | N/A |
STOPS |
| CLEAR |
|
|
|
|
|
MANUAL | Gives the user 10 seconds of manual control of the camera to allow the operator to move the | ||
CONTROL | camera to the desired position before the menu returns to its previous state. |
| |
|
|
|
|
WASH WIPE | Sets the wash position by pointing the camera at the washer nozzle | RIGHT TO SET | current |
POSITION | and pressing right to set. | POS | camera |
|
|
| position |
|
|
|
|
SET ZERO | Sets the zero degree (North) position when using the compass | RIGHT TO SET | N/A |
POS | direction captions. For example, point the camera North, Set Zero Pos, | POS |
|
| resulting in the caption correctly displaying the compass heading. |
|
|
|
|
|
|
UPPER LEFT | Soft Stops enable the user to set up an imaginary box within which the | RIGHT TO SET | Cleared |
AND LOWER | camera can move. There is only one zone available which is defined by | POS |
|
RIGHT SOFT | first setting the Top Left and then the Bottom Right of the zone. Once |
|
|
STOP | activated the MIC cannot be moved beyond the area set. |
|
|
|
|
|
|
LEFT AND | These 2 settings define the limits within which the camera will pan at | RIGHT TO SET | Cleared |
RIGHT AUTO | the “Auto Pan Speed” when the “Auto Pan” feature is activated. | POS |
|
PAN LIMITS |
|
|
|
|
|
|
|
MAP AUX TO | This option opens a submenu that allows certain features of the | WIPER, | N/A |
PRESET | camera which would normally be controlled through Aux commands to | WASHER, |
|
| be mapped to Go To Preset commands. The features available for this | DIGITAL |
|
| are Wiper, Washer, Digital Zoom, Auto Iris, Auto Focus, and Auto Pan. | ZOOM, |
|
| For each function there are 3 options: Control, On Preset, and Off | AUTO IRIS, |
|
| Preset. The control field denotes if the function is activated by the | AUTO FOCUS, |
|
| normal aux command or through a preset. The other 2 options set the | AUTO PAN |
|
| preset number to activate or deactivate each function. This provides |
|
|
| the ability to run all of the camera’s standard auxiliaries from a wider |
|
|
| range of control systems with varying direct aux support. |
|
|
| Note: If the control field of any of the functions is set to Go To Preset, |
|
|
| then the feature will not work using a standard button from a normal |
|
|
| controller. Similarly, if mapped to an Aux command, the preset values |
|
|
| indicated will have no effect. |
|
|
|
|
|
|
FIND END | Rotates the tilt axis first down then up to its mechanical limit stops. It | RIGHT TO | N/A |
STOPS | then stores a “soft” limit a few units back from these for normal use. | START |
|
| Note: manual control is not available during this process. |
|
|
|
|
|
|
RESET TO | Resets to the default settings for all OSD menus. | CONFIRM | N/A |
DEFAULTS |
| RESET, NO |
|
|
|
|
|
5.7.1 | Factory Defaults |
| Restores the camera unit to the Factory Default settings. See Section 5.14.1 Factory Defaults, |
| page 49. |
5.7.2 |
|
| The Pelco protocols (D and P) support 8 different auxiliaries, but do not define what function |
each should perform. This feature enables the 8 available auxiliaries to be set to any of the 8 available functions (Auto Focus, Digital Zoom, Auto Iris, Wiper, Washer, OSD and Backlight). By default, the auxiliaries are mapped as follows:
Bosch Security Systems, Inc. | User’s Manual | F.01U.173.601 2.0 2010.11 |