Bosch Appliances 500 user manual FCC & Ices Information, A. and Canadian Models Only

Page 8

8

en Safety

MIC Series 500 Camera

 

 

 

Environmental statement - Bosch has a strong commitment towards the environment. This unit has been designed to respect the environment as much as possible. Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid electrostatic discharge.

NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostatic-sensitive printed circuit boards.

Fuse rating - For security protection of the device, the branch circuit protection must be secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC Section 60).

Grounding and polarization - This unit may be equipped with a polarized alternating current line plug (a plug with one blade wider than the other blade). This safety feature allows the plug to fit into the power outlet in only one way. If unable to insert the plug fully into the outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the polarized plug.

Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for earth grounding). This safety feature allows the plug to fit into a grounded power outlet only. If unable to insert the plug into the outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the safety purpose of the grounding plug.

Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive force or shock may damage the unit.

Outdoor signals - The installation for outdoor signals, especially regarding clearance from power and lightning conductors and transient protection, must be in accordance with NEC725 and NEC800 (CEC Rule 16-224and CEC Section 60).

Permanently connected equipment - Incorporate a readily accessible disconnect device in the building installation wiring.

Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible. Power disconnect - Units have power supplied whenever the power cord is inserted into the power source. The power cord is the main power disconnect for all units.

Power lines - Do not locate the camera near overhead power lines, power circuits, or electrical lights, nor where it may contact such power lines, circuits, or lights.

Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information.

NOTICE!

This is a class B product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

FCC & ICES Information

(U.S.A. and Canadian Models Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

F.01U.173.601 2.0 2010.11

User’s Manual

Bosch Security Systems, Inc.

Image 8
Contents MIC Series 500 Camera Page Table of Contents Appendices 1Safety Important Safety InstructionsSafety Precautions Important Notices Coax groundingFCC & Ices Information A. and Canadian Models OnlyInformations FCC ET Ices DisclaimerCopyright TrademarksCustomer Support and Service Parts List UnpackingAdditional Tools Required Quantity Part1Features 2Power3Description 3Video4Mounting Part DescriptionAdjusting the MIC 500 Series Camera Pan body fixing screwsCanting in progress Adjusting the Rain Shield for Inverted Operation Remove screwsMounting the MIC 500 Series Camera Electrical Connections Earthing the MIC 500 Series CameraLightning Protection 13 Composite cable before connection Red Navigating the Menus Menu Item Description Exit1MIC Setups Menu Available only via the menu see .1.1 Config Mode,Setting Options Default ON/OFFTour ON/OFF OSDActivate Feature Menu 3Preset Tour MenuConfig Mode Image Flip Pan Reverse Tilt Reverse PrivacyRandom Tours Tour Setting ValueCreate/Modify Tour Tour Point Preset Position Dwell Time Pattern Tour MenuRecording a Pattern Tour Preview TourGoto Preset 5Presets MenuLearn Preset 6Communications Menu Manual ControlAdvanced Setups Menu Menu Item Description Options DefaultWipe Mode INTWipes Hour AutoFactory Defaults Re-map Pelco Aux Pelco D and P Protocols onlyAlarms Menu Relay 2 Status SET with Alarm Normally ClosedAux Number Function Menu Item Description OptionsAlarm Relays and Re-arm Time 9Sony Set MenuRelay Relay Activation Relay StateMapping to a MIC 500 Series Camera Function Exposure Shutter Priority 4 SET ShutterNumber Function ValueOn / OFF Setting OptionsSetting Values Available Aperture Reset / Plus 1 / Minus Aperture Set Low Lux Brightness Value Iris Setting Gain Setting Exposure Comp Value Iris Setting Gain Setting Focus Pos Focus DistanceIris Value Iris Setting Gain Value Gain SettingCaptions Menu Shutter Value Shutter Speed10.1 Default Caption 10.2 Preset Captions10.4Setting Captions 10.3 Sector CaptionsBlank Single Blank Save Single Save Sector /4 Sector Caption11.2Setting the Privacy Zones Privacy Menu11.1 Mask / Clear Whole Menu Item OptionsPot Test Menu 13MIC Information MenuGoto Preset Mapping Sony SET Current MIC Settings Auto Alarm OFF Multi Alarm Alarm RearmWipe Mode Normal WASH-WIPE OFF Control Card Data Serial Issue 8A14Set User Access Menu 13.1 MIC Information MenusOSD OFF 14.1 Factory DefaultsSetting Default Value Help Menu 16Self DiagnosisSupport USA EmeaAppendices MIC 500 Series Aux ControlsPreset Number Go To / Shot Preset Function MIC 500 Preset ControlsPreset Number Learn and Go to Preset Function Preset Number Learn Preset Function MIC 500 Model Numbers and Descriptions Model No DescriptionPage Bosch Security Systems, Inc
Related manuals
Manual 8 pages 56.48 Kb