Bosch Appliances 500 user manual Navigating the Menus

Page 22

22 en Navigating the MenusMIC Series 500 Camera

5

Navigating the Menus

The MIC 500 Series Camera is programmed through the on-screen display (OSD) menus. Each displays a list of parameters or submenus that you can select. To access the main menu, use one of two (2) methods:

–PC-based control system where you must identify preset command 85.

–Manual control via a compatible joystick

If the control system does not support presets or is limited to a preset number less than 85, tilt the unit upward until it hits the mechanical stop point, and then hold the joystick for approximately 10 seconds. The menu appears. To access the main menu via manual control:

1.Press Shot + 85 + Enter (Bosch controller). The main menu appears.

2.If this is the first time that you are using the camera, or if it is locked, you must enter the password to access all menu options.

3.Move the joystick down to ENTER PASSWORD, then move it to the right to enter the sub- menu. PASSWORD “0000” appears.

4.Move the joystick to the right. The “0000” turns green and the first number starts to blink.

5.Move the joystick up to change the first “0” to a “1”. The password should now be “1000,” which is the only valid password and can never be changed.

6.Move the joystick to the left to exit the menu. PASSWORD VALID appears.

–Tips to remember when navigating throughout the menus via the control:

–If the menu receives no manual controls for three (3) minutes, it automatically closes, returning the camera to its previous state. Any settings not saved are lost.

–Menu items appear in white, with the current item highlighted in either blue or green. If a line is highlighted in blue, use the up and down commands to move through the menu. If the line is highlighted in green, use the up and down commands to scroll through the settings for that option.

For numbers, move the joystick up to increase the numbers, and down to decrease the numbers. Move the joystick left and right to move between numbers.

–A right command can do one of two things: Move into the current option displaying all the options available, or select the current option by changing from blue to green, allowing the user to select a new value for this setting.

–A left command goes back a menu level or sets the setting that you just modified.

–Up and down commands scroll through the list and right to move into the next level of the menu. Pressing right on EXIT turns off the menu.

–For some menu items there are slight differences. For example, the Set-up Tour and Sony Set options from the main page request a number before moving into the settings. This sequence is: Select SETUP TOUR, then send right. Use the up and down to move between tour numbers, and then right again to enter the tour sub menus. The contents of the first screen is dependent on the level of user access defined by the installer under the password locked section of the menu.

MAIN MENU

1/2

MIC SETUPS

ACTIVATE FEATURE

PRESET TOUR

PATTERN TOUR

PRESETS

COMMUNICATIONS

ADVANCED SETUPS

ALARMS

MAIN MENU

2/2

SONY SET

CAPTIONS

PRIVACY

POT TEST

MIC INFORMATION

SET USER ACCESS

HELP

EXIT

F.01U.173.601 2.0 2010.11

User’s Manual

Bosch Security Systems, Inc.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents MIC Series 500 Camera Page Table of Contents Appendices 1Safety Important Safety InstructionsSafety Precautions Important Notices Coax groundingFCC & Ices Information A. and Canadian Models OnlyInformations FCC ET Ices DisclaimerCopyright TrademarksCustomer Support and Service Additional Tools Required Parts ListUnpacking Quantity Part3Description 1Features2Power 3Video4Mounting Part DescriptionAdjusting the MIC 500 Series Camera Pan body fixing screwsCanting in progress Adjusting the Rain Shield for Inverted Operation Remove screwsMounting the MIC 500 Series Camera Lightning Protection Earthing the MIC 500 Series CameraElectrical Connections 13 Composite cable before connection Red Navigating the Menus Menu Item Description Exit1MIC Setups Menu Available only via the menu see .1.1 Config Mode,Tour Setting Options DefaultON/OFF ON/OFF OSDConfig Mode Activate Feature Menu3Preset Tour Menu Image Flip Pan Reverse Tilt Reverse PrivacyCreate/Modify Tour Tour Setting ValueRandom Tours Recording a Pattern Tour Tour Point Preset Position Dwell TimePattern Tour Menu Preview TourLearn Preset 5Presets MenuGoto Preset 6Communications Menu Manual ControlAdvanced Setups Menu Menu Item Description Options DefaultWipes Wipe ModeINT Hour AutoFactory Defaults Re-map Pelco Aux Pelco D and P Protocols onlyAux Number Function Alarms MenuRelay 2 Status SET with Alarm Normally Closed Menu Item Description OptionsRelay Relay Activation Alarm Relays and Re-arm Time9Sony Set Menu Relay StateNumber Mapping to a MIC 500 Series Camera FunctionExposure Shutter Priority 4 SET Shutter Function ValueSetting Values Available Setting OptionsOn / OFF Aperture Reset / Plus 1 / Minus Aperture Set Low Lux Brightness Value Iris Setting Gain Setting Exposure Comp Value Iris Setting Gain Setting Focus Pos Focus DistanceIris Value Iris Setting Gain Value Gain SettingCaptions Menu Shutter Value Shutter Speed10.4Setting Captions 10.1 Default Caption10.2 Preset Captions 10.3 Sector CaptionsBlank Single Blank Save Single Save Sector /4 Sector Caption11.1 Mask / Clear Whole 11.2Setting the Privacy ZonesPrivacy Menu Menu Item OptionsPot Test Menu 13MIC Information MenuWipe Mode Normal WASH-WIPE OFF Goto Preset Mapping Sony SETCurrent MIC Settings Auto Alarm OFF Multi Alarm Alarm Rearm Control Card Data Serial Issue 8A14Set User Access Menu 13.1 MIC Information MenusSetting Default Value 14.1 Factory DefaultsOSD OFF Support USA Help Menu16Self Diagnosis EmeaAppendices MIC 500 Series Aux ControlsPreset Number Learn and Go to Preset Function MIC 500 Preset ControlsPreset Number Go To / Shot Preset Function Preset Number Learn Preset Function MIC 500 Model Numbers and Descriptions Model No DescriptionPage Bosch Security Systems, Inc
Related manuals
Manual 8 pages 56.48 Kb
Top Page Image Contents