Bosch Appliances 500 1MIC Setups Menu, Available only via the menu see .1.1 Config Mode

24 en Navigating the MenusMIC Series 500 Camera

5.1MIC Setups Menu

This section contains some of the more commonly modified settings for the MIC 500 Series Camera. Pressing right on an option changes the highlight color to green and allows the modification of the current setting value.

MAIN MENU 1/2

MIC SETUPS

ACTIVATE FEATURE

PRESET TOUR

PATTERN TOUR

PRESETS

COMMUNICATIONS

ADVANCED SETUPS

ALARMS

MIC SETUPS	1/2
CONFIG	UPRIGHT
AUTO HOME	ON
HOME TO	PRESET
WASH-WIPE	OFF
OSD	OFF
POS DISPLAY	OFF
AUTO ALARM	OFF

MIC SETUPS	2/2
DIGITAL ZOOM	ON
AUTO FLIP	OFF
SELF DIAGNOSIS

Menu Item	Description
CONFIG	Available only via the menu see Section 5.1.1 Config Mode, page 26.
AUTO HOME	Enables the unit to remain stationary when set to OFF or until the next user input. With Auto
	Home turned on, the MIC 500 Series Camera can be can be configured to either move to the
HOME TO
	home position (preset 1), start preset tour 1, or play pattern tour 1 using the “Home To”
	setting. The amount of time before this takes place can be set to 30 seconds, 1 minute, 5
	minutes, or 1 hour using the “Home Time” Setting in “Advanced Controls.”
WASH-WIPE	Upon activation, the camera moves to a saved position (Wash Wipe Position, Advanced
	settings), which should be set to look at the washer nozzle, starts the washer pump, and turns
	the wiper on. Once released, the unit returns to its original position, stops the washer pump,
	and continues wiping for a few seconds. This process only takes place if the Wash Wipe
	command is turned on; otherwise, the camera just activates the washer pump and will not
	move. If use of an external washer is required, then either the MIC-WKT (washer nozzle and
	bracket and MIC-WSH card) or MIC-WKT-IR (washer nozzle and bracket) kits should be
	purchased to enable a third party washer pump to be installed (see separate MIC-WKT manual).
OSD (on-screen	Displays the camera module information icons on the video, such as zoom position, white
display)	balance mode, shutter speed etc. This is only displayed when there are no captions on the
	screen.
POS DISPLAY	Indicates the current heading in degrees of the MIC 500 Series Camera in pan and tilt relative to
	its zero position, this is set during installation. The MIC 500 Series Camera takes 0° as North, so
	when the MIC 500 Series Camera is installed ensure the unit is pointed towards North, on a
	level tilt, then use “Set Zero Pos” in “Advanced Controls.” When activated, the position display
	shows the current compass heading North, South, East or West in a 1 or 2 character code N,
	NW, W, SW, S etc, along with an accurate pan and tilt bearing. The display is shown in white
	and resembles “N PAN: 125 TILT: 10."
AUTO ALARM	Enables use for both single or multi alarm functionality. With Auto Alarm on, the MIC moves to
	the Auto Alarm position (as configured using Cam-set, or “Alarms” - “Learn Alarm Pos”) upon
	detection of a tamper line input. If Auto Alarm is turned off, the MIC 500 Series Camera ignores
	any change in status of the tamper line which terminates in the MIC power supply, see MIC
	power supply manual for further details.
DIGITAL ZOOM	Provides both optical and digital zoom. On some systems, there is the option of selecting digital
	zoom, however with others the control system always outputs commands to continue into
	digital zoom which may not always be desirable. To stop this, there is an override function,
	Digital Zoom, which if turned off will not go into digital no matter what the keyboard sends out,
	and if activated will allow digital zoom as the controller dictates.

F.01U.173.601 2.0 2010.11 User’s Manual Bosch Security Systems, Inc.