Cisco Systems 4300 manual Motion detection controls Enable Motion Detection check box

Page 71

Chapter 4 Viewing Live Video

Table 4-1 Camera Video/Control Window Controls (continued)

Control

Description

Motion detection controls

Note These controls appear when you click the Up Arrow in the Motion Detection area and are available only viewing the primary (H.264) stream.

Enable Motion Detection check box

Enables the motion detection feature and displays a grid over the video image.

When motion detection is enabled, the IP camera monitors activity in the video field areas that you specify. If activity at a defined level occurs in any of these areas, the IP camera generates an alert and takes the actions that are configured as described in the “Event Notification Window” section on page 3-10.

To designate specific areas that the IP camera monitors for activity, select the areas by clicking each grid cell over the area. A red border indicates a selected area. To deselect an area, click it again.

You can configure the following levels for areas that the IP camera monitors for activity:

•Sensitivity—Designates the relative amount of activity that the IP camera must detect in the area before it generates an alert. A lower value means that more, or faster, activity is required to trigger an alert. A higher value means that less, or slower, activity is required. The default value is 50.

•Threshold—Designates the percentage of pixels that the IP camera must identify as changed in the area before it generates an alert. The camera detects pixel changes at the defined sensitivity level. The default threshold value is 50.

To configure sensitivity or threshold, right-click a grid cell that has a red border and then drag the Sensitivity and Threshold sliders to the desired values. Alternatively, enter a value from 1 through 100 for an option and press the Enter key. To reset the sensitivity and threshold to their default values of 50, click Restore. These configuration settings affect the cell that you select. If the cell is part of a group of horizontally or vertically (but not diagonally) adjacent cells, the settings affect all cells in the group.

Cisco Video Surveillance 4300 and 4500 High-Definition IP Cameras User Guide

	OL-19609-04	4-7

Image 71

Contents Text Part Number OL-19609-04 Americas HeadquartersCopyright 2009-2011 Cisco Systems, Inc. All rights reserved N T E N T S Log Windows Organization OverviewPreface Overview IP Camera FeaturesIP Camera Physical Details Front of IP Camera Adjusting Back Focus on the IP Camera section onRear of IP Camera Side of IP Camera Described in the Resetting the IP Camera section onPackage Contents DC Auto Iris Lens Connector PinoutsGetting Started Installing the IP CameraAction Explanation Action Explanation Action Explanation Before you Begin Performing the Initial Setup of the IP CameraProcedure Protocol//ipaddress Accessing the IP CameraIP Camera Window Links Understanding the IP Camera User InterfaceField Description IP Camera WindowsLink Description Channel 1 and Channel Adjusting Back Focus on the IP CameraLAN IP IO Port StatusResetting the IP Camera Powering the IP Camera On or OffSection on Reset Type Procedure RemarksInitial Setup of the IP Camera OL-19609-04 Accessing Navigating the Configuration Windows Configuring and Managing the IP CameraSnmp Feature Setup WindowsStreaming Streaming Settings WindowResolution Primary fps Secondary fps Current Channel Area Streaming Setup AreaOption Description Video Area Audio Setup AreaMicrophone Area Camera Settings WindowVideo Adjustments Area Day Night Filter Area Described in , Viewing Live VideoIO Ports Video Overlay Settings WindowIO Ports Settings Window Text Overlay AreaOutput Ports Pan Tilt Settings WindowInput Ports Area Pan/Tilt Area RS-232 SettingsEvent Notification Window Event Triggering Area Option Email Notification Area Patrol Sequence Window Patrol Sequence Area Analytics Windows Network Setup WindowsBasic Settings Window Basic Device Operations Area Basic Settings AreaIP Addressing Window IP Addressing Area Time Settings WindowClone PC Time button Set Time Mode AreaYou click Save Settings Local Time AreaShow Neighbors button Discovery Settings WindowNTP Server Settings Area Cisco Discovery Protocol CDP AreaSnmp v3 Area Snmp Settings WindowSnmp v2c Area 8000000901IPv4addresshex 802.1x Settings Window EAP-FAST Configuration Options IP Filter Settings WindowEAP-PEAP Configuration Options Filter Entries Area QoS Settings WindowClass of Service CoS Area IP Filter AreaAccount Initialization Window Administration WindowsDifferentiated Services DiffServ Area SSH Administrator Accounts AreaAccess Protocols Area User List Area User Settings WindowDelete button Maintenance Settings WindowChange button Reboot Area Reboot button Factory Default AreaRestore button Reset buttonDevice Information Area Firmware Settings WindowAddressing Window section on Details button Firmware Maintenance AreaUpgrade button Device Processes WindowLog Windows Password Complexity WindowLog Setup Settings Window Log Setup Settings Window, Local Log Window,Syslog Settings Area Local Log Settings AreaLocal Log Window Log messages, see -25 on Log List AreaExplanation Severity Ethsignaldegrade DefaultsrestoredDevicerebootauto DevicerebootmanualPowersupplyfailure LoginOutputonereset OutputtworesetStopstream TimedstswitchTimeregswitch StartstreamVideo controls Control DescriptionVideo image controls Streaming Settings Window section onMirror button Image tools Hotspot Zoom buttonHotspot Pan/Tilt Save Snapshot buttonAudio controls Full Screen buttonPreset button Presets controlsSet Current Preset as Add Preset PositionMotion detection Pan/tilt speed controlsMotion detection controls Enable Motion Detection check box Full Screen check Save Settings buttonTroubleshooting Troubleshooting Numerics IN-2 Https HttpIN-4 LEDIN-5 IN-6 IN-7 IN-8