Cisco Systems 4300 manual Powering the IP Camera On or Off, Resetting the IP Camera

Page 22

Chapter 2 Getting Started

Powering the IP Camera On or Off

To adjust the back focus, perform the following steps while viewing video from the camera. For information about viewing video, see Chapter 4, “Viewing Live Video.”

Procedure

Step 1 With a lens attached to the IP camera, use the 0.9mm Allen wrench that is supplied with the IP camera to loosen the focus ring hex screw.

This screw is on the bottom of the camera just behind the focus ring.

Step 2 Adjust the back focus by aiming the IP camera at an object that is at least 15 feet (4.5 meters) away and rotating the focus ring to obtain a clear image as follows:

•For a variable-focus lens, obtain a sharp picture in both wide-angle and telephoto positions.

•For a zoom lens, ensure that the object of interest remains in focus throughout the entire zoom range of the lens.

Step 3 Use the Allen wrench to tighten the focus ring hex screw.

Powering the IP Camera On or Off

The IP camera does not include an on/off switch. You power it on or off by connecting it to or disconnecting it from a power source. When you power off the IP camera, configuration settings are retained.

To power on the IP camera, take either of these actions:

•Use an STP (shielded twisted pair) Category 5 or higher network cable to connect the IP camera to a network switch that provides 802.3af compliant PoE

•Use an optional 12 VDC or 24VAC power adapter to connect the IP camera to a wall outlet

To power off the IP camera, take either of these actions:

•If the IP camera is receiving PoE, disconnect the network cable

•If the IP camera is receiving power through the power adapter, unplug the adapter from the wall or disconnect it from the camera

Resetting the IP Camera

You reset the IP camera by pressing the Reset button on the rear of the device (see Figure 1-3 on page 1-5). There are various reset types, as described in Table 2-4.

You also can also perform these reset operations from the Maintenance Settings window as described in the “Maintenance Settings Window” section on page 3-29.

	Cisco Video Surveillance 4300 and 4500 High-Definition IP Cameras User Guide
2-10	OL-19609-04

Image 22

Contents Americas Headquarters Text Part Number OL-19609-04Copyright 2009-2011 Cisco Systems, Inc. All rights reserved N T E N T S Log Windows Overview OrganizationPreface IP Camera Features OverviewIP Camera Physical Details Adjusting Back Focus on the IP Camera section on Front of IP CameraRear of IP Camera Described in the Resetting the IP Camera section on Side of IP CameraDC Auto Iris Lens Connector Pinouts Package ContentsInstalling the IP Camera Getting StartedAction Explanation Action Explanation Action Explanation Procedure Performing the Initial Setup of the IP CameraBefore you Begin Accessing the IP Camera Protocol//ipaddressUnderstanding the IP Camera User Interface IP Camera Window LinksLink Description IP Camera WindowsField Description IO Port Status Adjusting Back Focus on the IP CameraLAN IP Channel 1 and ChannelPowering the IP Camera On or Off Resetting the IP CameraInitial Setup of the IP Camera Reset Type Procedure RemarksSection on OL-19609-04 Configuring and Managing the IP Camera Accessing Navigating the Configuration WindowsFeature Setup Windows SnmpResolution Primary fps Secondary fps Streaming Settings WindowStreaming Option Description Streaming Setup AreaCurrent Channel Area Audio Setup Area Video AreaVideo Adjustments Area Camera Settings WindowMicrophone Area Described in , Viewing Live Video Day Night Filter AreaText Overlay Area Video Overlay Settings WindowIO Ports Settings Window IO PortsInput Ports Area Pan Tilt Settings WindowOutput Ports Event Notification Window RS-232 SettingsPan/Tilt Area Event Triggering Area Option Email Notification Area Patrol Sequence Window Patrol Sequence Area Basic Settings Window Network Setup WindowsAnalytics Windows IP Addressing Window Basic Settings AreaBasic Device Operations Area Time Settings Window IP Addressing AreaLocal Time Area Set Time Mode AreaYou click Save Settings Clone PC Time buttonCisco Discovery Protocol CDP Area Discovery Settings WindowNTP Server Settings Area Show Neighbors buttonSnmp v2c Area Snmp Settings WindowSnmp v3 Area 8000000901IPv4addresshex 802.1x Settings Window EAP-PEAP Configuration Options IP Filter Settings WindowEAP-FAST Configuration Options IP Filter Area QoS Settings WindowClass of Service CoS Area Filter Entries AreaDifferentiated Services DiffServ Area Administration WindowsAccount Initialization Window Access Protocols Area Administrator Accounts AreaSSH User Settings Window User List AreaChange button Maintenance Settings WindowDelete button Reset button Factory Default AreaRestore button Reboot Area Reboot buttonAddressing Window section on Firmware Settings WindowDevice Information Area Device Processes Window Firmware Maintenance AreaUpgrade button Details buttonLog Setup Settings Window, Local Log Window, Password Complexity WindowLog Setup Settings Window Log WindowsLocal Log Settings Area Syslog Settings AreaLocal Log Window Log List Area Log messages, see -25 onExplanation Severity Devicerebootmanual DefaultsrestoredDevicerebootauto EthsignaldegradeOutputtworeset LoginOutputonereset PowersupplyfailureStartstream TimedstswitchTimeregswitch StopstreamControl Description Video controlsStreaming Settings Window section on Video image controlsSave Snapshot button Image tools Hotspot Zoom buttonHotspot Pan/Tilt Mirror buttonFull Screen button Audio controlsAdd Preset Position Presets controlsSet Current Preset as Preset buttonPan/tilt speed controls Motion detectionMotion detection controls Enable Motion Detection check box Save Settings button Full Screen checkTroubleshooting Troubleshooting Numerics IN-2 Http HttpsLED IN-4IN-5 IN-6 IN-7 IN-8