VBrick Systems VB6000 Maintenance Mode CLI Operation, Command, Description, Entry, ex or exit

Page 105

Maintenance Mode

•The Telnet and/or Command Line Interface (CLI) prompt after you login is VBMaintMode> and displays one of t he following codes.

Code 10	Operating system failed to load or the flash is corrupted.

Code 20	Critical system files are missing or corrupted.

Code 30	The Hardware Watchdog has failed.

Code 50	Invalid Flash parameters found, defaults used.

Code 60	Corrupted Bootline, default used.

Code FF	Application failed to start up successfully either because of the
	configuration or another problem. The VBrick appliance will enter
	Maintenance Mode if the appliance does not boot properly on four
	consecutive attempts.

Maintenance Mode CLI Operation

After logging into Maintenance Mode as the Administrator, the VBMainMode> prompt is displayed and one or more of the following command sequences can be issued from the Command Line Interface. By design, in Maintenance Mode, after the user initiates changes and applies, it is necessary to manually save and reboot. For more about the Command Line Interface, see the Network Appliance Installation Guide.

TTo use CLI commands in Maintenance Mode:

1.Make all desired changes, in any sequence, using the commands in Table 6.

2.When done type c nt a to apply the changes.

3.Type sv to save the configuration.

Table 6. CLI Commands

Command	Description	Entry

e 2	To start the editor mode. This	Type e 1 to display editor status.
	command must be entered prior to
	any other command.

ex or exit	To leave the current menu level and
	move up through the menu system.

rb	Reset the VBrick	Enter y (yes to reset).

sd	Set the configuration parameters to	Confirmation is requested.
	factory defaults, except the Ethernet
	IP parameters

sfd	Set the configuration parameters to	Confirmation is requested.
	factory defaults, including the
	Ethernet IP parameters

c nt 5 x	To enable or disable DHCP	1 – Disable DHCP
		2 – Enable DHCP

VBrick MPEG-2 Appliance Admin Guide

97

Image 105

Contents VB4000-5000-6000 Series Network Video Appliances VBrick v4.1 MPEG-2 Appliance Admin GuideCopyright FCC NoticeAbout VBrick Systems MPEG-2 Admin Guide Contents2. MPEG-2 Configuration 1. Introduction4. Status 3. SDI Configuration6. Maintenance 5. Diagnostics7. Maintenance Mode 8. VBStarIndex MPEG-2 Admin Guide OrganizationGetting Help Font Conventions Printer-FriendlyItalics are used to emphasize specific words or phrases Chapter IntroductionOverview VBSSMArchiver and Recorder Functionality Mixed Model AppliancesConfiguration ModelIntroduction Figure 1. Archiver/Recorder Functionality2007 VBrick Systems, Inc MPEG-2 Overview MPEG-2 ConfigurationOptimizing MPEG-2 Performance OptionApplicable Model Absolute Maximum Transport Rates MPEG-2 Configuration RecommendationsDest1, Dest2 DecoderDest1, Dest2 Configuration Network Ethernet Configuration Networkcan be letters, numbers or hyphens Gateway IP AddressConfiguration Network Routing Domain Name ServerNetwork Time Synchronization Routing Method Configuration Network Management Configuration Network IPv6 Configuration BillboardBillboard FTP Using the BillboardBillboard File Types Billboard URLsLocal URL Remote URLVideo Input Creating a BillboardFont Sizes Transparent BackgroundConfiguration Decoder Configuration Decoder Videoapplying this parameter will cause the VBrick to reset Configuration Decoder Audio Configuration Decoder Network Receive Address Configuration Decoder Picture-In-Picture Picture in Picture Configuration Encoder Transport Configuration EncoderConfiguration Encoder Video Video Format \h or \H - Host Name \d or \D - Current Date\t or \T - Current Time Reference Distance Configuration Encoder Audio Audio Input Configuration Encoder Destination 1/Destination2 Destination Address Configuration Encoder Announce SAP support replacement characters. The replacement text is only shown in Announce Common Informationfollowing string IPMask=xxx.xxx.xxx.xxx where SAP for Destination 1 and/orConfiguration Encoder Text Insertion Configuration Recorder Configuration PumpConfiguration FTP File Transfer Configuration ConferencingConferencing Configuration Passthrough COM1 Configuration PassthroughPassthrough State Responder Passthrough State Initiator Destination Configuration System Configuration Passthrough COM2Dedicated Address Mode System Configuration System Generalparameters before you can enable Network Time Synchronization on this windowFront Panel LCD Display Configuration System SNMP TrapsProgram Files\VBrick\VB6000\Download\ReleaseVxxxxxx Event Description NumberEvent Description Improving Security Configuration System SecurityConfiguration System Logging Configuration Video On Demand Configuration Script Management Configuration Script Management Event TriggeringRun Scripts Using IWS Figure 2. Script Management - Part Run Scripts Using the IR Remote Control Run Scripts Using Event TriggersSample Script Scripting Notes Configuration Script Management Auto ConfigurationXML Header Introduction SDI ConfigurationVertical Offset Correction SDI Audio Input 2007 VBrick Systems, Inc Status System Information StatusSystem Model Status Network Status Codec Status Network Statusor 100Mbit GeneralInterface Status Network Status RoutingStatus Decoder Status Status Network Status Network Time Status Network Status IPv6MPEG-2 Decoder Status Decoder State Status Encoder Status MPEG-2 Encoder Status Status Hard Drive StatusStatus Hard Drive Status General Network Status Hard Drive Status PumpStatus Hard Drive Status Recorder Status FTP Server Status Status System Log Status System Log ConfigStatus System Log Traps Status System Log System EventStatus User Information Status System Log System InfoStatus User Information Main Board Status User Information Slot1/Slot2 User Information Version 2007 VBrick Systems, Inc Diagnostics Network Tests DiagnosticsUser Diagnostics Diagnostics Network Tests Ping TestDiagnostics Network Tests Trace Route Test Trace Route Test Results Diagnostics Network Tests Data Test Diagnostics Device Test Diagnostics Decoder Color Bars Diagnostics Hard Drive 2007 VBrick Systems, Inc Maintenance Device Information MaintenanceMaintenance Default All Configuration Maintenance Read/Write ConfigurationMaintenance Read/Write Read From Device Read Configuration Data from Device Maintenance Read/Write Write To Device Maintenance Change Usernames & Passwords Maintenance Usernames & Passwords Change Usernames & PasswordsWrite Configuration Data to Device User Name Default User Name Maintenance Usernames & Passwords Change SNMPv3 PasswordsDefault Password User LevelUser Name Maintenance Mode Maintenance Mode Features Maintenance Mode IndicatorsMaintenance Mode Limitations Command Maintenance Mode CLI OperationEntry ex or exitCommand VBStar Recording vs. Archiving VBStar PumpConfiguration Pump General store files on the C drive. The C drive has limited space and isreserved for VBrick firmware Configuration Pump Destination See MPEG-2 Configuration Encoder Announce SAP on page Configuration Pump Announce SAPConfiguration Pump Operation VBStar Record Using Mixed ModelsFilename Syntax Rules Recording Batch FilesBatch Wrap Point and Record Duration Configuration Recorder General FTP Server Enable Configuration Recorder Network Configuration Recorder Operation Recorder State VBStar FTP File Transfer Configuration FTP File Transfer ServersFTP Server Configuration FTP File Transfer TransfersFTP Status FTP Queue Operation VBStar Status2007 VBrick Systems, Inc Index Page Page Wallingford, Connecticut 06492, USA VBrick Systems, Inc 12 Beaumont Road

Related manuals

Manual 86 pages 2.72 Kb

Manual 156 pages 46.18 Kb