Micon IP-220E manual IGuardware

Page 31

Chapter 4: iGuardware

Click the depressed button to go back to the original window size.

b. Custom update Window -- use this if you want to monitor only a specific area within the viewing window.

On the video window, RIGHT click, hold and drag to the desired window zoom size. A thin line will outline the chosen window size.

Release and a smaller window is shown. Video in this smaller window will be updated while those outside are ‘frozen’.

Click the depressed button to go back to the original window size. Or use the horizontal zoom bar (see below).

Click and drag the green knob along the horizontal bar to zoom in an out. Zoom range from 1 time to 16 times.

Click and drag the green knob along the horizontal bar to change the current image resolution. Resolution range from 320x240 low/mid/high quality, to 640x480 low/mid/high quality.

Clicking once will cause the camera to pan left by 1 deg.

Click and hold and the camera will pan increasingly faster to the left.

Clicking once will cause the camera to pan right by 1 deg.

Click and hold and the camera will pan increasingly faster to the left.

30

Image 31

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Server Authentication Email Notification SettingEmail Address Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection System Information Information System StatusIi. Network Status IGuard System Status Current ConnectionsIGuard Current Connections Event LogSetting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPDynamic DNS Iv. EthernetVi. PPPoE User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event NotificationIGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailIv. Email Address Book System SettingsSystem Time Iv. Snmp Settings Iii. LED SettingsIi. System Restart About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationDdns Port Forwarding Appendix a Router ConfigurationDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary