Micon IP-220E manual Appendix a Router Configuration

Page 71

Appendix A: Router Configuration

Microsoft (http://www.microsoft.com/hardware/broadbandnetworking)

MN-100 – Wired Base Station

MN-500 – Wireless Base Station

1.Log into your router using your router IP.

2.Open the Bass Station Management Tool, and then click Security.

3.On the Security menu, click Port Forwarding, and then click Set up persistent port forwarding.

4.In the Enable checkbox, check in the checkbox.

5.In the Description box, type a description of the server field such as: iGuard Web.

6.In the Inbound port boxes, type in: 80 – 80. (i.e. from Port 80 to Port 80)

7.In the Type box, select the protocol as TCP.

8.In the Private IP address box, type in the IP Address of the iGuard network camera. For example, type in: 192.168.0.5.

9.In the Private port boxes, these values are automatically filled in from Step 6 and should already show 80 – 80.

10.On the next empty line, repeat steps 4-9, except this time the Description should be iGuard Cam and the Inbound/Private port boxes should be 9001 – 9001 (UDP). The protocol and private IP address should be the same.

11.Click Apply to save the changes you have made. iGuard should now be configured to work with your router and be accessible from the internet.

70

Image 71

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Email Address Email Notification SettingServer Authentication Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection Ii. Network Status Information System StatusSystem Information IGuard System Status Current ConnectionsIGuard Current Connections Event LogSetting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPVi. PPPoE Iv. EthernetDynamic DNS User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event NotificationIGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailSystem Time System SettingsIv. Email Address Book Ii. System Restart Iii. LED SettingsIv. Snmp Settings About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationDemilitarized Zone DMZ Appendix a Router ConfigurationDdns Port Forwarding BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary