Micon IP-220E manual Motion Detection, Camera a or Camera B Enable

Page 51

Chapter 5: iGuard Web Manager

Fig.38 iGuard Event : Camera A or B Motion Detected

5.2.4.2 Motion Detection

This page allows the administrator to set motion detection functions for the cameras.

i.Camera A (or Camera B) “Enable”

To activate motion detect, the administrator has two options;

a.“Always On” or

b.“On Schedule”, the administrator can set up to 4 different time slots for motion detection.

“Detection Sensitivity”

This will determines level of change before motion capture is triggered.

“Send image every”

Select a value between 1 to 5 seconds.

“Stop sending emails after ## email(s) or image idle for ## second(s)”

iGuard will stop sending on the lower of the two conditions. You can set between 1, 3, 5, 7 and 10 seconds. Emails can be set from 1 to 99999 pieces, or 0 for stop sending email only when image idle occurred.

“Schedule”

If set to “On Schedule” in the above section, the administrator can then input the four preferred schedule time slots for motion detection. Time must be entered in 24hr format.

50

Image 51

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Email Notification Setting Server AuthenticationEmail Address Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection Information System Status System InformationIi. Network Status IGuard System Status Current ConnectionsIGuard Current Connections Event LogSetting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPIv. Ethernet Dynamic DNSVi. PPPoE User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event Notification IGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailSystem Settings Iv. Email Address BookSystem Time Iii. LED Settings Iv. Snmp SettingsIi. System Restart About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationAppendix a Router Configuration Ddns Port ForwardingDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary