Micon IP-220E manual Appendix D Q&A, Q2. Can I use other USB Camera to connect to iGuard?

Page 83

Appendix D: Glossary

Appendix D: Q&A

Q1. I have set a permission level without first setting an "Administrator" first and now I can't change anything.

You will need to update the firmware. Download the firmware and use iGuard Utility to upload it into iGuard. Once completed, the Username and Passwords will be reset to default. Always remember to save your iGuard configuration for use later.

Q2. Can I use other USB Camera to connect to iGuard?

Yes, provided that the camera is using VIMICRO chip. You will have to check with the manufacturer of the USB camera. Currently, about 60% to 70% of the cameras produced in China uses this chip.

Q3. I get the following message, when I click on ActiveX

Click on the top margin, and install ActiveX. Also make sure that you have firmware v2.37, if not you'll need to upgrade.

Q4. How can I view images from my web enabled PDA?

Please make sure that you have a GRPS enabled PDA. Use the browser and type in http://xxx.xxx.xxx.xxx/image.cgi (where xxx is the WAN IP address or your Domain Name). You will then be directed to this page;

82

Image 83

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Email Address Email Notification SettingServer Authentication Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection Ii. Network Status Information System StatusSystem Information IGuard System Status Current ConnectionsIGuard Current Connections Event LogSetting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPVi. PPPoE Iv. EthernetDynamic DNS User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event NotificationIGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailSystem Time System SettingsIv. Email Address Book Ii. System Restart Iii. LED SettingsIv. Snmp Settings About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationDemilitarized Zone DMZ Appendix a Router ConfigurationDdns Port Forwarding BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary