Micon manual IGuard IP-220E Hardware, Light color Condition description

Page 6

Chapter 2. :iGuard IP-220E Hardware

Chapter 2 iGuard IP-220E Hardware

Fig.2 iGuard IP-220E Camera

LED Status Indicators on iGuard

 

Light color

 

Signal definition

 

 

Condition description

 

 

Green

 

Power state

 

On: Normal power

 

 

 

 

 

 

 

 

 

 

 

 

Red

 

Error Condition

 

On: Error condition occurred

 

 

 

 

 

 

 

 

 

 

 

 

Orange

 

Logon state

 

On: When there

is user

logon

and

 

 

 

receive the image.

 

 

 

 

 

 

 

 

 

 

 

 

Yellow

 

USB data activity

 

Flash

when

there

is

data

 

 

 

transmit/receive on the USB.

 

 

 

 

 

 

 

 

 

 

 

 

Table.1 iGuard Status LED Indicator

 

 

 

 

 

Light indicators on iGuard LAN Port LED

 

Light color

 

Condition description

 

Green

On: Internet correspond speed is 100M

 

Flash: Data transmitting/receiving

 

 

 

Yellow

On: Internet correspond speed is 10M

 

Flash: Data transmitting/receiving

 

 

 

 

Table.2

iGuard LAN LED Indicators

5

Page 5 Page 7
Image 6
Page 5 Page 7
Contents IGuard Contents Page Features IntroductionPackage Contents IGuard IP-220E Hardware Light color Condition descriptionHardware Installation Installation Procedure StepInstalling iGuardware IGuardwareUsing iGuardware IGuard UtilitySetup Wizard IGuard Setup WizardIGuard Network Setup IGuard a/DSL Setup IGuard PPPoE Setup Launch iGuardManagerChapter.5 Click either one to Launch iGuard IP Configuration IGuard Web ManagerIP Configuration Set an IP Address for iGuard Device Password Reset Device PasswordUpgrade Firmware Ii. Management ProtocolIGuardware IGuardView IGuardView Screen ShotDevice Setting IGuardware Camera Setting Motion Detection Setting REDAvifilethree digit numerical sequence Email Notification Setting Server AuthenticationEmail Address Snmp Setting Using Snmp to update network portsCamera Monitor IGuardware IGuardware View SystemHelp IGuard Web Manager IntroductionIGuard Web Manager Web-Camera Selection Information System Status System InformationIi. Network Status Current Connections IGuard System StatusEvent Log IGuard Current ConnectionsBasic Settings Camera Settings Setting up Camera a Similar with Camera BIndividual Camera Configuration Network IP AddressIi. DNS Server IP Iii. Port NumberIv. Ethernet Dynamic DNSVi. PPPoE Account Settings User Account User NameCamera Advanced Settings Event Notification IGuard Permit Hours ConfigurationEvent Notification Send Email IGuard Event NotificationIGuard Event Selection List IGuard Event Start Up Camera a or Camera B Enable Motion DetectionIGuard Motion Detection IGuard Motion Detect Email Notification Image Recording Camera a or Camera B Begin End hhmmMail / FTP IGuard Email of Image RecordedFTP Settings FTP Server Ii. Email Settings E-mail ServerIii. Sending Test Mail IGuard test mail functionSystem Settings Iv. Email Address BookSystem Time Iii. LED Settings Iv. Snmp SettingsIi. System Restart Snmp setting AboutIi. Save / Restore Settings Save current Configuration AboutAppendix a Router Configuration Ddns Port ForwardingDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration Type in the camera’s IP address UDPDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix C Glossary Term DefinitionAppendix D Q&A Q2. Can I use other USB Camera to connect to iGuard?Q5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary
Top Page Image Contents