Micon IP-220E manual Q5. What is the effective length of the USB cable?

Page 84

Appendix D: Glossary

Click on either "Camera A (320*240)" or "Camera B (320*240)" to view the image.

Click "Refresh" to download the next image. Click "Back" to go back to the above page.

Q5. What is the effective length of the USB cable?

The industrial Standard for effective USB cable length is 5.0m from source to source. If you so decide to extend the length, you can purchase a USB extension

Q6. What is the effective length of the RJ-45 cable?

The Standard effective length per RJ-45 cable is 100m, you will need a hub per 100m extension, up to a maximum of 480m.

Q7. Can I use iGuard outdoors?

iGuard is designed primarily for indoor use. For outdoor use you will need a protective housing. This is not supplied.

Q8. Is the camera capable of zooming by adding a zoom lens?

You can add a zoom lens, but will have to adjust the zoom manually. The default camera does not support 'remote' zoom.

Q9. My iGuard is connected to a Router and I can see it in LAN but my friends can't see it from the Web? How do I set up iGuard for the web?

For users with DYNAMIC IP;

(a)Contact iGuard.com Customer Support for a DDNS account (self-registration coming soon) and register your iGuard cameras

83

Image 84

Contents IGuard Contents Page Features IntroductionPackage Contents IGuard IP-220E Hardware Light color Condition descriptionHardware Installation Installation Procedure StepInstalling iGuardware IGuardwareUsing iGuardware IGuard UtilitySetup Wizard IGuard Setup WizardIGuard Network Setup IGuard a/DSL Setup IGuard PPPoE Setup Launch iGuardManagerChapter.5 Click either one to Launch iGuard IP Configuration IGuard Web ManagerIP Configuration Set an IP Address for iGuard Device Password Reset Device PasswordUpgrade Firmware Ii. Management ProtocolIGuardware IGuardView IGuardView Screen ShotDevice Setting IGuardware Camera Setting Motion Detection Setting REDAvifilethree digit numerical sequence Email Notification Setting Server AuthenticationEmail Address Snmp Setting Using Snmp to update network portsCamera Monitor IGuardware IGuardware View SystemHelp IGuard Web Manager IntroductionIGuard Web Manager Web-Camera Selection Information System Status System InformationIi. Network Status Current Connections IGuard System StatusEvent Log IGuard Current ConnectionsBasic Settings Camera Settings Setting up Camera a Similar with Camera BIndividual Camera Configuration Network IP AddressIi. DNS Server IP Iii. Port NumberIv. Ethernet Dynamic DNSVi. PPPoE Account Settings User Account User NameCamera Advanced Settings Event Notification IGuard Permit Hours ConfigurationEvent Notification Send Email IGuard Event NotificationIGuard Event Selection List IGuard Event Start Up Camera a or Camera B Enable Motion DetectionIGuard Motion Detection IGuard Motion Detect Email Notification Image Recording Camera a or Camera B Begin End hhmmMail / FTP IGuard Email of Image RecordedFTP Settings FTP Server Ii. Email Settings E-mail ServerIii. Sending Test Mail IGuard test mail functionSystem Settings Iv. Email Address BookSystem Time Iii. LED Settings Iv. Snmp SettingsIi. System Restart Snmp setting AboutIi. Save / Restore Settings Save current Configuration AboutAppendix a Router Configuration Ddns Port ForwardingDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration Type in the camera’s IP address UDPDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix C Glossary Term DefinitionAppendix D Q&A Q2. Can I use other USB Camera to connect to iGuard?Q5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary