Micon IP-220E manual Tcp

Page 67

Appendix A: Router Configuration

D-Link (http://www.dlink.com)

DI-604/DI – 614+/DI-624

1.Log into your router using your router IP.

2.On the main page, click on Advanced at the top of the page.

3.On the left side of the page, click on Virtual Server. Note: Make sure DMZ host is disabled. If DMZ is enabled, it will disable all Virtual Server entries.

4.Enter the following information on the page:

Enable/Disable:	Enabled
Name:	iGuard - Webpage
Private IP:	Type in the camera’s IP address, for example: 192.168.0.5
Protocol Type:	TCP
Private Port:	80
Public Port:	80
Schedule:	Always

5.Click Apply to save the settings.

6.Enter the following information on the page:

Enable/Disable: Enabled

Name:iGuard - Webpage

Private IP:	Type in the camera’s IP address, for example: 192.168.0.5
Protocol Type:	UDP
Private Port:	9001
Public Port:	9001
Schedule:	Always

7.Click Apply o save the settings. iGuard should now be configured to work with your router and be accessible from the internet.

DI-704/704P

1.Log into your router using your router IP.

2.On the main page, click on Advanced at the top of the page.

3.On the Virtual Server page, enter the following information; For ID#1:

Service Port:	80
Service IP:	Type in the camera’s IP address, for example: 192.168.0.5

66

Image 67

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Server Authentication Email Notification SettingEmail Address Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection System Information Information System StatusIi. Network Status IGuard System Status Current ConnectionsIGuard Current Connections Event LogSetting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPDynamic DNS Iv. EthernetVi. PPPoE User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event NotificationIGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailIv. Email Address Book System SettingsSystem Time Iv. Snmp Settings Iii. LED SettingsIi. System Restart About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationDdns Port Forwarding Appendix a Router ConfigurationDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary