Micon IP-220E manual Ii. DNS Server IP, Iii. Port Number

Page 43

Chapter 5: iGuard Web Manager

Fig.24 iGuard IP Address Settings

“IP Address”

This item determines iGuard IP Address.

“Subnet Mask”

This item sets iGuard Subnet Mask. The value is normally 255.255.255.0

“Gateway”

This item is to set iGuard Gateway.

“Obtain an IP address”

This allows the user to choose either to set iGuard IP Address manually or via DHCP. iGuard will reboot after the above settings have been changed.

ii.DNS Server IP

Fig.25 iGuard IP DNS Server IP

“Primary DNS Server IP”

This item sets iGuard primary DNS Server IP address.

“Secondary DNS Server IP”

This item sets iGuard secondary DNS Server IP address. iGuard will use the secondary DNS Server IP address if the Primary DNS Server IP address is not working.

iii.Port Number

Fig.26 iGuard Port Settings

“HTTP Port Number”

By default the port number is 80. You have to use a different port number here if you host a website on the same network, if your ISP blocks port 80 traffic, or if you have multiple iGuard on the network

“Communication to Camera Port Number”

42

Image 43

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Server Authentication Email Notification SettingEmail Address Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection System Information Information System StatusIi. Network Status IGuard System Status Current ConnectionsIGuard Current Connections Event Log Setting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPDynamic DNS Iv. EthernetVi. PPPoE User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event NotificationIGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailIv. Email Address Book System SettingsSystem Time Iv. Snmp Settings Iii. LED SettingsIi. System Restart About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationDdns Port Forwarding Appendix a Router ConfigurationDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary