Micon IP-220E manual IGuardware, Installing iGuardware

Page 9

Chapter 4: iGuardware

Chapter 4: iGuardware

iGuardware is a collection of two utility programs: iGuard Utility and iGuardview. You can use the iGuard Utility to quickly setup multiple iGuard units and you can use iGuardview to monitor multiple cameras, and maybe most importantly to perform motion tracking (V2.5 and above only). If you have a DHCP server on the network, the iGuard will obtain an IP address automatically, and you can enter this IP address in IE to launch the web manager (Chapter 5).

4.1 Installing iGuardware

Insert the software CD (or download from www.iguard.com) and click on setup if autorun does not start.

Fig.3 iGuardware Installation

"iGuard Utility - This is a program that helps the user perform quick installation. It will detect the current configuration and take the user through the necessary network setup.

a.Click the ‘iGuard Utility’ button to start installation.

b.After the step by step installation is completed, the iGuard Utility group will appear in Windows ’Start’ Â ‘Program Group’. “iGuard” Click this to start the program.

"iGuardView - This is a windows based program designed to allow user to control a large number of iGuard module located either in a LAN or on a WAN.

"Read User’s Manual - Click to read iGuard’s User Manual. You will need Adobe Acrobat Reader v5.0 or higher.

8

Image 9

Contents IGuard Contents Page Introduction FeaturesPackage Contents Light color Condition description IGuard IP-220E HardwareHardware Installation Step Installation ProcedureIGuardware Installing iGuardwareIGuard Utility Using iGuardwareIGuard Setup Wizard Setup WizardIGuard Network Setup IGuard a/DSL Setup Launch iGuard IGuard PPPoE SetupManagerChapter.5 Click either one to Launch iGuard IGuard Web Manager IP ConfigurationIP Configuration Set an IP Address for iGuard Reset Device Password Device PasswordIi. Management Protocol Upgrade FirmwareIGuardware IGuardView Screen Shot IGuardViewDevice Setting IGuardware Camera Setting RED Motion Detection SettingAvifilethree digit numerical sequence Email Notification Setting Server AuthenticationEmail Address Using Snmp to update network ports Snmp SettingCamera Monitor IGuardware IGuardware System ViewHelp Introduction IGuard Web ManagerIGuard Web Manager Web-Camera Selection Information System Status System InformationIi. Network Status IGuard System Status Current ConnectionsIGuard Current Connections Event LogSetting up Camera a Similar with Camera B Basic Settings Camera SettingsIndividual Camera Configuration IP Address NetworkIii. Port Number Ii. DNS Server IPIv. Ethernet Dynamic DNSVi. PPPoE User Account User Name Account SettingsCamera IGuard Permit Hours Configuration Advanced Settings Event NotificationIGuard Event Notification Event Notification Send EmailIGuard Event Selection List IGuard Event Start Up Motion Detection Camera a or Camera B EnableIGuard Motion Detection IGuard Motion Detect Email Notification Camera a or Camera B Begin End hhmm Image RecordingIGuard Email of Image Recorded Mail / FTPIi. Email Settings E-mail Server FTP Settings FTP ServerIGuard test mail function Iii. Sending Test MailSystem Settings Iv. Email Address BookSystem Time Iii. LED Settings Iv. Snmp SettingsIi. System Restart About Snmp settingAbout Ii. Save / Restore Settings Save current ConfigurationAppendix a Router Configuration Ddns Port ForwardingDemilitarized Zone DMZ BEFSR41 Appendix a Router Configuration UDP Type in the camera’s IP addressDescription IGuard Camera Internet Port 9001 to Type TCP Appendix a Router Configuration Dell TrueMobile 2300 Wireless Broadband Router Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration TCP Type in the camera’s IP address Appendix a Router Configuration TCP Appendix a Router Configuration Appendix B IP Address, Subnet and Gateway Subnet Mask Routing and Filtering Subnetting and Subnet MasksTerm Definition Appendix C GlossaryQ2. Can I use other USB Camera to connect to iGuard? Appendix D Q&AQ5. What is the effective length of the USB cable? If iGuard is connected to a Router or IP Share then Q13. There is no Port Forwarding Section in my Router Appendix D Glossary