Kenwood TS-570S, TS-570D UP/DOWN buttons, Split button, TF-SET button, Clear button, 9MVFO button

3 GETTING ACQUAINTED

1

@1@2@3@4@5

2	PF	POWER				HF TRANSCEIVER TS-570D
	ATT	PRE-AMP
	VOX	PROC
	SEND	AT TUNE
3			CH1	CH2	CH3	MIC	LSB
	PHONES		1	2	3
							USB
			ANT	REC	FINE	PWR	CW
			4	5	6
							FSK

UP

DOWN

MR

		N.R.
		B.C.
		CW TUNE
		FILTER
		RIT/XIT
M.IN	–	+

DSP SLOPE

HIGHLOW

T	I
U	H
	G
C		H
W		C
O
L	T	U

AF RF

46

28

010

	MIC	NB	AGC/TONE REV		KEY
4		7	8	9	FM
					AM
			F.LOCK		DELAY MENU 1MHz

CLR 0 ENT

5
6	!7Frequency control buttons
	These buttons control functions related to selecting a
	frequency, a VFO, or a memory channel.
7	•	UP/DOWN buttons
		Press to step through all Amateur bands
		consecutively {page 13} or to step the transceiver
8		frequency in 1 MHz increments {page 29}. Also
		used for making selections from the Menu
		{page 16}, and to check Start and End frequencies
		for the Scan function {page 43}.
9	•	SPLIT button
		Press to use split-frequency operation which allows
		a different transmit frequency and receive frequency
		{page 23}.
10
	•	M/V button
		Press to select either Memory or VFO mode
		{page 40}.
11
	•	TF-SET button
		While operating split-frequency, press to monitor or
		change your transmit frequency {page 23}.
12
	•	A=B button
		Press to copy the data in the currently selected VFO
		over to the other VFO {page 30}.
13	•	A/B button
		Press to select either VFO A or VFO B {page 13}.
		Also, in menu mode, press to select either Menu A
14		or Menu B {page 16}.
	•	CLEAR button
		Press to reset the RIT/XIT frequency offset to zero
15		{pages 30, 32}.
	•	RIT button
		Press to switch ON or OFF the Receive Incremental
		Tuning function {page 30}.
16
	•	XIT button
		Press to switch ON or OFF the Transmit
		Incremental Tuning function {page 32}.

SPLIT TF-SET A/B RIT

CH IF SHIFT SQL

46

M/V A=B CLEAR XIT

28

SCAN M>VFO M.IN

010

!7 !8!9 @0

!8SCAN button

Press to start and stop Scan functions {pages 46, 47}.

!9M>VFO button

Press to transfer data from a memory channel to a VFO {page 42}.

@0M.IN button

Writes data into a memory channel {page 39} or selects Memory Scroll mode {page 41}.

@1Quick Memory buttons

Controls the Quick Memory function {page 44}.

•M.IN button

Press to write data into Quick Memory {page 44}.

•MR button

Press to recall data from Quick Memory {page 45}.

@2FILTER button

Press to select the receive filter bandwidth in SSB, CW, FSK, or AM mode {pages 36, 38}, or press to select either narrow-band or wide-band transmit deviation in FM mode {page 22}.

Note: Selecting the narrow filter bandwidth in SSB mode requires the optional YK-88SN-1 filter {page 36}.

@3CW TUNE button

Press to activate the automatic zero-beat function for CW mode {page 21}.

@4B.C. button

Press to switch ON or OFF the DSP Beat Cancel function {page 38}.

@5N.R. button

Press to toggle between Noise Reduction 1, Noise Reduction 2, and OFF {page 38}.

8