| 12 OPERATOR CONVENIENCES |
BEEP FUNCTION | Consult the following table to select a function. |
| Selecting OFF assigns no function to the button. |
1
The purpose of the Beep function is to provide an audible signal that conveys information. There are three types of signals:
•To confirm that a button has been pressed.
•To report an error condition; Morse codes are used for some errors.
•To confirm that the selection was completed by pressing [MIC], [PWR], [KEY], [DELAY], or [FILTER] again.
When selecting an operating mode, a Morse code abbreviation for that mode is heard.
Mode | Morse Code Output |
| ||
|
|
|
|
|
LSB | ·– · · |
| (L) | |
|
|
|
|
|
USB | · ·– |
| (U) | |
|
|
|
|
|
CW | – ·– · |
| (C) | |
CW | – ·– · | ·– · | (CR) | |
|
|
|
|
|
FSK | ·– · |
| (R) |
|
FSK | ·– · | ·– · | (RR) | |
AM | ·– |
| (A) | |
Function | Function | |
Number | ||
| ||
|
| |
00 to 40 | Selects Menu | |
| No. 00 to 40. | |
| See “MENU | |
| CONFIGURATION”. | |
50 | Monitor | |
51 | Voice 1 | |
52 | Voice 2 | |
|
| |
53 | DSP Filter | |
Monitor | ||
|
60QUICK MEMO [MR]
61QUICK MEMO [M.IN]
62[SPLIT]
63
64[A/B]
65[M/V]
66[A=B]
Function Function Number
67[SCAN]
68[M>VFO]
69[M.IN]
70[CW TUNE]
71[CH 1]
72[CH 2]
73[CH 3]
74[FINE]
75[F. LOCK]
76[CLR]
Selects Menu No. 48 to 51.
80 to 83 Ex: 82 selects Menu No. 50.
99 OFF
2
3
4
5
6
7
FM | · ·– · | (F) |
You can change the volume of the beep output via Menu No. 01.
1Press [MENU].
2Press [A/B] to select Menu A or Menu B.
3Turn the MULTI/CH control to select Menu No. 41, 42, 43, 44, or 45.
8
DISPLAY DIMMER
The Display illumination can be switched between 5 levels via Menu No. 00.
PROGRAM FUNCTION BUTTON
The transceiver allows you to customize the function of the front panel [PF] button. When using the optional
•Directly select Menu No. 00 to 40, 48 to 51. No need to press [MENU] and turn the MULTI/CH control.
•Activate a function that is supported by no other front panel buttons.
•Activate the same function as one of the front panel buttons.
4Press [UP], [DOWN], Mic [UP], or Mic [DWN] to select a function number.
• Consult the above table to select a function.
5Press [MENU] to exit Menu mode.
The default values are as follows:
•Front panel [PF]: Voice 1
• | Mic [PF1]: [A/B] | • | Mic [PF2]: [SPLIT] |
• | Mic [PF3]: [M/V] | • | Mic [PF4]: Monitor |
Note:
◆Full Reset returns the functions of the PF buttons to default settings.
◆Function No. 84 accessible in step 4 is not currently available. Pressing the PF button with Function No. 84 assigned will simply cause the transceiver to display a string of error codes.
9
10
11
12
13
14
15
16
49