Kenwood TS-570S, TS-570D Operator Conveniences, Microprocessor Reset, Frequency Lock Function

Page 54

OPERATOR CONVENIENCES

1

MICROPROCESSOR RESET

If your transceiver seems to be malfunctioning, resetting the microprocessor default settings may resolve the problem.

The ANT 1/ANT 2 setting will automatically be stored in the current band. Each time you select the same band, the same setting will automatically be selected.

The frequency range of each band is shown below.

2

3

4

INITIAL SETTINGS

For each VFO, the factory defaults for operating frequency and mode are as follows:

VFO A: 14.000.000 MHz/ USB

VFO B: 14.000.000 MHz/ USB

The Conventional and Quick memory channels have no data stored.

Frequency Range

(MHz)

0.03~ 2.50

2.50~ 4.10

4.10~ 7.50

7.50~ 10.50

10.50 ~ 14.50

Frequency Range

(MHz)

14.50~ 18.50

18.50~ 21.50

21.50~ 25.50

25.50~ 30.00

30.00~ 60.00 (TS-570S)

5

6

7

8

PARTIAL RESET

Do Partial Reset if a button or control does not function according to the instructions in this manual. The following are not erased by Partial Reset.

Memory channel data

Menu settings

Antenna tuner preset data

ANT 1/ANT 2 data.

To do Partial Reset, press [A/B]+ POWER ON.

“HELLO” appears on the display.

Note: Connect an external antenna tuner to the ANT 1 connector only. After connecting this tuner correctly and selecting ANT 1, the internal tuner will always be bypassed.

FREQUENCY LOCK FUNCTION

Frequency Lock disables some buttons and controls to prevent you from accidentally activating a function or disturbing current settings.

Press [F.LOCK] to toggle Frequency Lock ON or OFF.

“F.LOCK” appears when the function is ON.

9

10

11

12

13

14

15

16

FULL RESET

Do Full Reset if you want to erase all data in all memory channels. In addition, this function resets all settings, that you customized, to the factory defaults, i.e. menu settings, antenna tuner preset data, etc.

To do Full Reset, press [A=B]+ POWER ON.

“HELLO” appears on the display.

Note: The IF filter selection in Menu No. 46 will not be reset.

SWITCHING ANT 1/ ANT 2

After connecting antenna feed line to the ANT 1 connector and/or ANT 2 connector on the rear panel, select ANT 1 or ANT 2, depending on which antenna is used for transmitting and receiving.

Press [ANT] to select ANT 1 or ANT 2.

“ANT 1” or “ANT 2” appears to show which antenna is selected.

The following buttons and controls are disabled by Frequency Lock:

Tuningcontrol

 

 

MULTI/CHcontrol

QUICK MEMO [MR]

QUICK MEMO [M.IN]

[FINE]

[REV]

 

[CLR]

[ENT]

[LSB/USB]

[CW/FSK]

[FM/AM]

[1MHz]

 

[UP]/[DOWN]

[SPLIT]

[A/B]

 

[M/V]

[A=B]

[SCAN]

 

[M>VFO]

[M.IN]

 

 

 

 

 

Note:

After activating Frequency Lock, the MULTI/CH control and [UP]/[DOWN] are still available in Menu mode.

After activating Frequency Lock, you can still change the transmit frequency with the Tuning control while using the TF-SET function.

After activating Frequency Lock, the MULTI/CH control is still available for selections other than frequency and memory channel changes.

After activating Frequency Lock, [CLR] is still available in some situations.

48

Image 54
Contents TS-570S Applicable Model Supplied AccessoriesAccessory Part Number Intelligent Digital Enhanced Communications SystemWriting Conventions Followed FeaturesKEY+ Power on KEY2Contents Installing Options Memory FeaturesOptional Accessories Specifications Appendix COM Connector Protocol IndexPower Lines Power SourcePower Cable Protection CleaningAPPROX. Loss dB PER 30 Meters 100 Feet InstallationAntenna Connection Correctly Matched 50 Ω LineGround Connection DC Power Supply ConnectionInstallation Lightning ProtectionAccessory Connections Front PanelRear Panel RF control Fully clockwise Your First QSOSet the following as specified AF control Fully counterclockwise If Shift control Center SQL controlYour Getting Acquainted Front PanelGetting Acquainted TF-SET button UP/DOWN buttonsSplit button Clear buttonMicrophone KEY and Paddle jacks Rear PanelGND post EXT SP jackDisplay @8USB @6M.SCR@7LSB #1FSKOperating Basics Switching Power ON/OFFAdjusting Volume Selecting VFO a or VFO BSelecting a Frequency Selecting a ModeAdjusting Squelch Front Panel MeterTransmitting Selecting Transmit PowerPress PWR again to complete the setting Microphone GainMenu Setup What is a MENU?Menu A/ Menu B Page Page Menu Setup Cross Reference for Menu FunctionsBasic Communicating SSB TransmissionTX SIDETONE/ RX Pitch Frequency CW TransmissionBasic Communicating Auto ZERO-BEATTX Deviation Selection FM TransmissionAM Transmission Press FilterTF-SET Transmit Frequency SET Specialized CommunicatingSPLIT-FREQUENCY Operation UP/DWNArrl 10-METER Band Plan FM Repeater OperationSpecialized Communicating Mode/ActivitySpecialized Communicating Selecting Subtone Frequency When you are calledWhen you make a call Continuous or Burst SUBTONES?Rtty Frequencies Digital OperationRtty Frequency Shift Keying Iaru Region A./CanadaPacket Frequencies Mode MeaningMode Data Rate Europe/AfricaSlow Scan TV/ Facsimile Sstv FrequenciesCommunicating Aids ReceivingSelecting Your Frequency RX Equalizer RIT Receive Incremental TuningCommunicating Aids AGC Automatic Gain ControlVOX VOICE-OPERATED Transmit Microphone Input LevelXIT Transmit Incremental Tuning Communicating Aids Speech ProcessorEqualizing Transmit Audio SSB/FM/AM Transmit InhibitChanging Transmit Bandwidth SSB/AM BandwidthCW BREAK-IN Auto WeightingReversible Auto Weighting Electronic KeyerChanging LOCKED-WEIGHT BUG KEY FunctionCW Message Memory Noise Blanker Rejecting InterferenceIf Filter If ShiftDSP Tools AttenuatorPreamplifier Rejecting InterferenceNoise Reduction Beat CancelSetting NR2 Time Constant CW/ FSK ModesStoring Data in Memory Memory FeaturesConventional Memory Simplex ChannelsMemory Recall Memory FeaturesSplit-Frequency Channels Memory Recall and ScrollMemory-VFO Split Operation Memory ScrollTemporary Frequency Changes To use a memory channel for receivingMemory Features Memory Transfer Memory VFO TransferChannel Channel Transfer Erasing Memory Channels Full ResetStoring Frequency Ranges Confirming Start/End FrequenciesVOX ON/OFF Storing Into Quick MemoryMemory Channel Lockout RIT ON/OFF XIT ON/OFFMemory Features Recalling Quick Memory Temporary Frequency ChangesQuick Memory VFO Transfer Scan Hold ScanProgram Scan Transceiver provides the following types of ScanALL-CHANNEL Scan Memory ScanScan Group ScanOperator Conveniences Microprocessor ResetSwitching ANT 1/ ANT Frequency Lock FunctionBeep Function Display DimmerProgram Function Button Quick Data Transfer Setting UPUsing Quick Transfer Operator ConveniencesComputer Control Using a TransverterMenu Setting Communication ParametersPresetting Automatic Antenna TunerAT Tune again Message Playback DRU-3A Digital Recording UnitOptional Recording MessagesChanging Volume Sending MessagesChanging Inter-message Interval Menu New ModeSteps VoicePC-1A Optional AccessoriesDRU-3A PG-2ZInstalling Options Removing the Bottom CaseInstalling Options VS-3 Voice Synthesizer UnitFilters SO-2 TEMPERATURE-COMPENSATED Crystal Oscillator TcxoCut the leads of the R503 and R504 resistors Computer Compatible TransceiverLinear Amplifier Connecting Peripheral EquipmentRtty Equipment Antenna TunerMCP and TNC Pin No FunctionService MaintenanceService Note CleaningAccessing the Internal Fuse Internal AdjustmentsMaintenance Reference Frequency CalibrationFollowed TroubleshootingProblem Probable Cause Corrective Action DSP Slope LOW control orChanging Receive Press LSB/USB, CW/FSK, orPress LSB/USB or FM/AM to Repeater Operation Communication ParametersFSK, FM Max 100 W Output powerTS-570S TS-570D Min Max 25 WSpecifications SSB, CW, FSKAppendix Hardware DescriptionControl Operation COMError Messages Computer Control CommandsAlphabetical Commands ParametersAlphabetical Command Table OFF/ONParameter Table FormatMenu Selection Table for EX Command UP/DOWNReading Command Tables Computer Control Command TablesDN UP DOWN/UP LK Frequency Lock MG MIC Gain RT RIT RX TX RX, TX VOX Function DSP VFOSstv