Kenwood TS-570D, TS-570S Transmitting, Microphone Gain, Selecting Transmit Power

Page 21

 

4 OPERATING BASICS

TRANSMITTING

3 Press [PWR] again to complete the setting.

Methods for transmitting include the following:

Note: The transmit power can be separately selected for the AM

mode independent of the other modes.

• Press [SEND].

 

1

Press and hold down Mic [PTT].

Connect a key or keyer paddle, select the CW mode, press [VOX] to switch ON the Break-in function, and close the key or keyer paddle.

PF POWER

ATT PRE-AMP

VOX

PROC

SEND

AT TUNE

For a detailed explanation on transmitting, refer to sections in “BASIC COMMUNICATING” beginning on page 20.

Note: When CW, FSK, or AM is selected, the transmit carrier level is automatically adjusted according to the selected mode.

MICROPHONE GAIN

The microphone gain is finely adjustable in the SSB or AM mode. A different level can be selected between when the Speech Processor {page 32} is ON and when the Speech Processor is OFF.

1Press [MIC].

The current microphone gain level appears. The default is 50.

MIC

PWR

KEY

DELAY

2

3

4

5

6

SELECTING TRANSMIT POWER

It’s wise, and required by law, to select the lowest transmit power that allows reliable communication. Reducing power lowers the risk of interfering with others on the band. On this transceiver, it is possible to change output power while transmitting.

1Press [PWR].

• The current transmit power appears.

2Press [SEND] or press and hold Mic [PTT].

• “TX” appears.

3SSB: While speaking into the microphone, adjust the MULTI/CH control so that the ALC meter reflects according to your voice level.

AM: While speaking into the microphone, adjust the MULTI/CH control so that the calibrated power meter slightly reflects according to your voice level.

7

8

9

MIC

PWR

KEY

DELAY

2Turn the MULTI/CH control counterclockwise to reduce power and clockwise to increase power.

• The displayed transmit power changes.

CH

QUICK MEMO

SSB/CW/FSK/FM:Transmit power can be changed from 5 W to 100 W in steps of 5 W.

AM:Transmit power can be changed from 5 W to 25 W in steps of 5 W.

CH

QUICK MEMO

4Press [SEND] again or release Mic [PTT].

• “TX” disappears.

5Press [MIC] again.

For the FM mode, set the microphone gain by accessing Menu No. 17 {page 17} and selecting either “L” (low) or “H” (high).

Note:

When using the optional MC-90 microphone in FM mode, select high microphone gain. The microphone sensitivity is low in FM mode and this may cause insufficient modulation.

When using a microphone that has an amplifier, be careful that the output of the amplifier is not too large.

10

11

12

13

14

15

16

15

Image 21
Contents TS-570S Accessory Part Number Supplied AccessoriesApplicable Model Intelligent Digital Enhanced Communications SystemKEY+ Power on FeaturesWriting Conventions Followed KEY2Contents Optional Accessories Memory FeaturesInstalling Options Specifications Appendix COM Connector Protocol IndexPower Cable Protection Power SourcePower Lines CleaningAntenna Connection InstallationAPPROX. Loss dB PER 30 Meters 100 Feet Correctly Matched 50 Ω LineInstallation DC Power Supply ConnectionGround Connection Lightning ProtectionAccessory Connections Front PanelRear Panel Set the following as specified AF control Your First QSORF control Fully clockwise Fully counterclockwise If Shift control Center SQL controlYour Front Panel Getting AcquaintedGetting Acquainted Split button UP/DOWN buttonsTF-SET button Clear buttonMicrophone GND post Rear PanelKEY and Paddle jacks EXT SP jackDisplay @7LSB @6M.SCR@8USB #1FSKAdjusting Volume Switching Power ON/OFFOperating Basics Selecting VFO a or VFO BAdjusting Squelch Selecting a ModeSelecting a Frequency Front Panel MeterPress PWR again to complete the setting Selecting Transmit PowerTransmitting Microphone GainMenu Setup What is a MENU?Menu A/ Menu B Page Page Cross Reference for Menu Functions Menu SetupSSB Transmission Basic CommunicatingBasic Communicating CW TransmissionTX SIDETONE/ RX Pitch Frequency Auto ZERO-BEATAM Transmission FM TransmissionTX Deviation Selection Press FilterSPLIT-FREQUENCY Operation Specialized CommunicatingTF-SET Transmit Frequency SET UP/DWNSpecialized Communicating FM Repeater OperationArrl 10-METER Band Plan Mode/ActivityWhen you make a call When you are calledSpecialized Communicating Selecting Subtone Frequency Continuous or Burst SUBTONES?Rtty Frequency Shift Keying Digital OperationRtty Frequencies Iaru Region A./CanadaMode Data Rate Mode MeaningPacket Frequencies Europe/AfricaSstv Frequencies Slow Scan TV/ FacsimileCommunicating Aids ReceivingSelecting Your Frequency Communicating Aids RIT Receive Incremental TuningRX Equalizer AGC Automatic Gain ControlMicrophone Input Level VOX VOICE-OPERATED TransmitCommunicating Aids Speech Processor XIT Transmit Incremental TuningChanging Transmit Bandwidth SSB/AM Transmit InhibitEqualizing Transmit Audio SSB/FM/AM BandwidthReversible Auto Weighting Auto WeightingCW BREAK-IN Electronic KeyerChanging LOCKED-WEIGHT BUG KEY FunctionCW Message Memory If Filter Rejecting InterferenceNoise Blanker If ShiftPreamplifier AttenuatorDSP Tools Rejecting InterferenceSetting NR2 Time Constant Beat CancelNoise Reduction CW/ FSK ModesConventional Memory Memory FeaturesStoring Data in Memory Simplex ChannelsSplit-Frequency Channels Memory FeaturesMemory Recall Memory Recall and ScrollTemporary Frequency Changes Memory ScrollMemory-VFO Split Operation To use a memory channel for receivingMemory Features Memory Transfer Memory VFO TransferChannel Channel Transfer Storing Frequency Ranges Full ResetErasing Memory Channels Confirming Start/End FrequenciesMemory Channel Lockout Storing Into Quick MemoryVOX ON/OFF RIT ON/OFF XIT ON/OFFMemory Features Recalling Quick Memory Temporary Frequency ChangesQuick Memory VFO Transfer Program Scan ScanScan Hold Transceiver provides the following types of ScanScan Memory ScanALL-CHANNEL Scan Group ScanSwitching ANT 1/ ANT Microprocessor ResetOperator Conveniences Frequency Lock FunctionBeep Function Display DimmerProgram Function Button Using Quick Transfer Setting UPQuick Data Transfer Operator ConveniencesMenu Setting Using a TransverterComputer Control Communication ParametersPresetting Automatic Antenna TunerAT Tune again Optional DRU-3A Digital Recording UnitMessage Playback Recording MessagesChanging Volume Sending MessagesChanging Inter-message Interval Steps New ModeMenu VoiceDRU-3A Optional AccessoriesPC-1A PG-2ZRemoving the Bottom Case Installing OptionsInstalling Options VS-3 Voice Synthesizer UnitFilters SO-2 TEMPERATURE-COMPENSATED Crystal Oscillator TcxoCut the leads of the R503 and R504 resistors Compatible Transceiver ComputerRtty Equipment Connecting Peripheral EquipmentLinear Amplifier Antenna TunerPin No Function MCP and TNCService Note MaintenanceService CleaningMaintenance Internal AdjustmentsAccessing the Internal Fuse Reference Frequency CalibrationProblem Probable Cause Corrective Action TroubleshootingFollowed DSP Slope LOW control orChanging Receive Press LSB/USB, CW/FSK, orPress LSB/USB or FM/AM to Communication Parameters Repeater OperationTS-570S TS-570D Max 100 W Output powerFSK, FM Min Max 25 WSSB, CW, FSK SpecificationsControl Operation Hardware DescriptionAppendix COMAlphabetical Commands Computer Control CommandsError Messages ParametersOFF/ON Alphabetical Command TableFormat Parameter TableUP/DOWN Menu Selection Table for EX CommandComputer Control Command Tables Reading Command TablesDN UP DOWN/UP LK Frequency Lock MG MIC Gain RT RIT RX TX RX, TX VOX Function DSP VFOSstv