Alpine DVA-9965 66-EN, Accessory List, Slide the mounting sleeve into the dashboard, Removal

Page 68

Installation
Accessory List
• Head unit	1
• Power Supply box	1
• Power cable	1
• S video cable	1
• RCA extension cable (for video signal)	1
• Mounting sleeve	1
• Screw (M5 ⋅ 8)	4
• Flange-head tapping screw (M4 ⋅ 14)	4
• Velcro Fasteners	2
• Front frame	1
• Remote Control	1
• Battery (CR2025)	1
• Carrying case	1
• Owner's Manual	1 set
Metal plate
Detachable
Front panel

Caution

When you install this unit in your car, do not remove the detachable front panel.

If the detachable front panel is removed during installation, you might press too hard and warp the metal plate that holds it in place.

1Mounting Sleeve

(Included) Dashboard

this unit

Slide the mounting sleeve into the dashboard.

2Screw

Hex Nut (M5)

*2

Bolt Stud

Metal

Mounting

Strap

*1

this unit

Ground Lead

Chassis

Reinforce the head unit with the metal mounting strap (not supplied). Secure the ground lead of the unit to a clean metal spot using a screw (*1) already attached to the vehicle’s chassis.

•For the screw marked “*2”, use an appropriate screw for the chosen mounting location.

Connect each input lead coming from an amplifier or equalizer to the corresponding output lead coming from the left rear of the DVA-9965. Connect all other leads of the DVA-9965 according to details described in the CONNECTlONS section.

3

Lock Pin

Slide the DVA-9965 into the dashboard. When the unit is in place, make sure the locking pins are fully seated in the down position. This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the detachable front panel.

Removal

1 Remove the detachable front panel.

2Use a small screwdriver (or similar tool) to push the locking pins to the “up” position (see above drawing). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock before unlocking the second pin.

3 Pull the unit out, keeping it unlocked as you do so.

<JAPANESE CAR>

Front Frame

Screws (M5 ⋅ 8) (Included)

this unit

Ground Lead

*3

Mounting Bracket

•Secure the ground lead of the unit to a clean metal spot using a screw (*3) already attached to the vehicle's chassis.

66-EN

Image 68

Contents DVA-9965 CHA-S634 CHA-1214 CHM-S630Contents Installation and Connections Operating Instructions USE only in Cars with a 12 Volt Negative GroundNever Attempt the Following Discs playable on this unit On handling compact discs CD/CD-R/CD-RW Move your finger on the GlideTouch bar to the left or right About the GlideTouch Bar OperationTouch or press the desired position on the GlideTouch bar Turning Power On and Off Initial System Start-UpAdjusting Volume Display Tilt AdjustmentLowering Volume Quickly Opening and Closing the Movable DisplayManual Storing of Station Presets Automatic Memory of Station PresetsTuning to Preset Stations RadioFrequency Search Function Playback11-EN Press g or f to select the desired track filePress FUNC. to activate the audio function mode Press the GlideTouch bar under RPT to select the RPT modeRepeat Play 12-ENX. Random Play Scanning ProgramsSearching from CD Text File/Folder Name Search concerning MP3/ WMAFolder Name Search mode File Name Search modeAbout MP3/WMA 14-ENTerminology 15-ENDVD/Video CD Playing DVD/Video CDIf a menu screen appears 16-ENPlaying Still Frames pausing Stopping Playback PRE-STOPStopping Playback Fast-forwarding/Fast-reversingSwitching the Audio Tracks Switching the Angle DVD onlyChapter/Track/Title Repeat Playback Video CDs with multiplex audioSwitching the Subtitles subtitle language DVD only Displaying the Disc Status DVD onlyDisplaying the Disc Status Video CD only 19-ENSound Setting GlideTouch bar Operation20-EN FuncSelecting the EQ mode Factory settings Setting Users EQ modeAdjusting and Storing the Parametric Equalizer Curve 21-ENAdjusting and Storing the Graphic Equalizer Curve Recalling the Stored Equalizer Curve22-EN Press and hold Menu for at least 2 secondsWay mode About the Crossover23-EN CrossoverAdjusting and Storing the Crossover Settings Press SOURCE/POWER to adjust the slopeAdjust the output level by turning the Rotary encoder WAY SystemRecalling the Stored Crossover Settings About Time CorrectionExample 1. Listening Position Front Left Seat Example 2. Listening Position All SeatsSetting the Time Correction Unit Adjusting and Storing the Time CorrectionPress Band to select a speaker to be adjusted Display Setup menu is displayed27-EN Recalling the Stored Time Correction SettingsSetting the MX Mode Other Functions Displaying the Text28-EN Press TitleBlackout Mode On and Off Setting the Multicolor IlluminationDisplaying Time Rear DVD FunctionPersonalize Data Download Operation About i-Personalize Data Download30-EN File name of download data shall be AU∗∗∗∗∗.MP3Data Downloading Downloading the Wallpaper31-EN Insert a CD-R/CD-RW disc containing dataDVD Setup DVD Setup OperationSetting the language Press Setup before inserting a disc, or when in stop modeSetting the TV Screen Setting the Country CodeSetting the Rating Level Parental Lock Press Return repeatedly until the Setup mode is deactivatedSetting the Digital Output Setting contents Bitstream / Lpcm34-EN Audio output/Optical digital audio outputCustom Setup Custom Setup Operation35-EN ENT36-EN Setup OperationGeneral Setting 37-EN Audio SettingDisplay Setting Demo Setting 38-ENStoring Channel Presets SAT Radio Receiver OptionalReceiving Channels with the SAT Radio Receiver Optional Checking the SAT Radio ID NumberSetting the Auxiliary Data Field Display Receiving Stored ChannelsChanging the Display Channel/Category Search FunctionSearching for a desired Song Searching by PlaylistSearching by artist name 41-ENQuick Search Random Play Shuffle M.I.XSearching by album name 42-ENRPT mode is canceled by selecting off 43-ENSong will be played back repeatedly Each press changes the displayChanger Optional Controlling CD Changer OptionalPlaying MP3 Files with the CD Changer Optional Multi-Changer Selection OptionalAdjustment Procedure for Dolby Surround 45-ENSetting the Speakers Set MX Mode of the External Audio ProcessorOver Adjustment 46-ENPerforming Time Correction Manually TCR/ Phase Switching Calculating the Time Correction47-EN = distance of farthest speaker Distance of other speakersGraphic Equalizer Adjustments Switching the PhaseInputting the Time Correction 48-ENParametric Equalizer Adjustments Setting Bass CompressorSpeaker Setup 49-ENSetting of Dolby Digital Adjusting the speaker levels Output LevelMixing bass sound to the rear channel Rear MIX 50-ENAdjusting the DVD Level Adjusting the acoustic image BI-PHANTOM51-EN BI-PHANTOM ON/OFFSelecting the Center Width Using the Pro Logic II Mode52-EN 53-EN Storing Settings in the MemoryGetting out the Preset Memory 54-EN Remote ControlControls on Remote Control 55-EN When Using the Remote ControlBattery Replacement 56-EN InformationAbout DVDs Terminology Dolby DigitalDolby Pro Logic Linear PCM audio LpcmFor details, see List of Language Codes58-EN List of Country Codes 59-EN60-EN Case of Difficulty BasicRadio CD/MP3/WMA/DVD/Video CDIndication for CD Player Indication for DVD/Video CD Player62-EN Picture is unclear or noisy Indication for SAT Receiver Mode Indication for CD Changer 63-EN Sirius to64-EN SpecificationsIndication for iPod Mode Installation and Connections 65-ENAccessory List 66-ENSlide the mounting sleeve into the dashboard Removal67-EN Installing the Power Supply UnitWhen mounting with Velcro fasteners Connections 68-ENAntenna Receptacle Power Antenna Lead Blue 69-ENConnect the External Monitor System Example70-EN 71-EN To prevent noise/interference in the audio systemLimited Warranty Page Page Page