Alpine DVA-9965 owner manual 69-EN, Antenna Receptacle Power Antenna Lead Blue

Page 71

1Antenna Receptacle

2Power Antenna Lead (Blue)

Connect this lead to the +B terminal of your power antenna, if applicable.

•This lead should be used only for controlling the vehicle's power antenna. Do not use this lead to turn on an amplifier, or a signal processor, etc.

3Remote Turn-On Lead (Blue/White)

Connect this lead to the remote turn-on lead of your amplifier or signal processor.

4Audio Interrupt In Lead (Pink)

5Illumination Lead (Orange)

This lead may be connected to the vehicle’s instrument cluster illumination lead. This will allow the backlighting of the unit to dim whenever the vehicle’s lights are turned on.

6Switched Power Lead (Ignition) (Red)

Connect this lead to an open terminal on the vehicle's fuse box or another unused power source which provides (+)12V only when the ignition is turned on or in the accessory position.

7Battery Lead (Yellow)

Connect this lead to the positive (+) post of the vehicle's battery.

8Fuse Holder (7.5A)

9Ground Lead (Black)

Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided.

!Monitor Control Lead (Front) (White/Pink)

Connect this to the Monitor Control Lead of the touch panel compatible front monitor.

"Monitor Control Lead (Rear) (White/Pink)

Connect this to the Monitor Control Lead of the touch panel compatible rear monitor.

#Remote Control Input Lead (Touch panel compatible front monitor) (White/Brown)

Connect this to the remote control output lead for the touch panel compatible front monitor.

$Remote Control Input Lead (Rear) (White/Brown)

Connect this to the remote control output lead for the rear monitor.

•If the optional remote control eye (KRE-500E) is connected, the remote control signal cannot be received.

%Power Supply Box

•Do not install the Power Supply Box at a location subjected to water such as under the floor mat or air conditioner. This may cause a malfunction.

•Do not bundle the Power Supply Box cable with other audio cables. Doing so may induce noise into your system.

•Keep the Power Supply Box converter away from the Antenna cables and the rear side of the unit, otherwise noise may be generated when receiving radio broadcast.

&Video Output Connector (Yellow)

Output the video

(Audio Output Connectors

RED is right and WHITE is left output the audio.

)Front Output RCA Connectors

RED is right and WHITE is left.

~Rear Output RCA Connectors

RED is right and WHITE is left.

+Subwoofer RCA Connectors

RED is right and WHITE is left.

,S Video output terminal

Outputs the video signal.

Connect a monitor that has a S video input terminal.

-Digital Output Terminal (Optical)

Use when combining fiber digital input compatible products.

.Remote Control Eye Jack

If a monitor other than Alpine is installed, it can still be controlled by the supplied remote control by installing the optional remote control eye (KRE-500E).

/Steering Remote Control Interface Connector

To steering remote control interface box.

:Power Supply Connector

;Setting the 3WAY/2WAY switch

Set the 3way/2way switch according to your audio system.

<RCA Extension Cable (sold separately)

=Ai-NET Connector

Connect this to the output or input connector of another device (CD Changer, Equalizer, INTERFACE ADAPTER FOR iPod™* etc.) equipped with Ai-NET.

* When connecting iPod, INTERFACE ADAPTER FOR iPod™ (KCA-420i) is required. For details on how to connect, refer to the Owner’s Manual of KCA-420i.

•You can input TV/video sound by connecting an optional Ai-NET/RCA Interface cable (KCA-121B) to this component.

>Ai-NET Cable (Included with CD Changer)

69-EN

Page 70 Page 72
Image 71
Page 70 Page 72
Contents DVA-9965 CHA-1214 CHM-S630 CHA-S634Contents Installation and Connections USE only in Cars with a 12 Volt Negative Ground Operating InstructionsNever Attempt the Following Discs playable on this unit On handling compact discs CD/CD-R/CD-RW Move your finger on the GlideTouch bar to the left or right About the GlideTouch Bar OperationTouch or press the desired position on the GlideTouch bar Initial System Start-Up Turning Power On and OffOpening and Closing the Movable Display Adjusting VolumeDisplay Tilt Adjustment Lowering Volume QuicklyRadio Manual Storing of Station PresetsAutomatic Memory of Station Presets Tuning to Preset StationsPress g or f to select the desired track file Frequency Search FunctionPlayback 11-EN12-EN Press FUNC. to activate the audio function modePress the GlideTouch bar under RPT to select the RPT mode Repeat PlayFile/Folder Name Search concerning MP3/ WMA X. Random PlayScanning Programs Searching from CD Text14-EN Folder Name Search modeFile Name Search mode About MP3/WMA15-EN Terminology16-EN DVD/Video CDPlaying DVD/Video CD If a menu screen appearsFast-forwarding/Fast-reversing Playing Still Frames pausingStopping Playback PRE-STOP Stopping PlaybackVideo CDs with multiplex audio Switching the Audio TracksSwitching the Angle DVD only Chapter/Track/Title Repeat Playback19-EN Switching the Subtitles subtitle language DVD onlyDisplaying the Disc Status DVD only Displaying the Disc Status Video CD onlyFunc Sound SettingGlideTouch bar Operation 20-EN21-EN Selecting the EQ mode Factory settingsSetting Users EQ mode Adjusting and Storing the Parametric Equalizer CurvePress and hold Menu for at least 2 seconds Adjusting and Storing the Graphic Equalizer CurveRecalling the Stored Equalizer Curve 22-ENCrossover Way modeAbout the Crossover 23-ENWAY System Adjusting and Storing the Crossover SettingsPress SOURCE/POWER to adjust the slope Adjust the output level by turning the Rotary encoderExample 2. Listening Position All Seats Recalling the Stored Crossover SettingsAbout Time Correction Example 1. Listening Position Front Left SeatDisplay Setup menu is displayed Setting the Time Correction UnitAdjusting and Storing the Time Correction Press Band to select a speaker to be adjusted27-EN Recalling the Stored Time Correction SettingsSetting the MX Mode Press Title Other FunctionsDisplaying the Text 28-ENRear DVD Function Blackout Mode On and OffSetting the Multicolor Illumination Displaying TimeFile name of download data shall be AU∗∗∗∗∗.MP3 Personalize Data Download OperationAbout i-Personalize Data Download 30-ENInsert a CD-R/CD-RW disc containing data Data DownloadingDownloading the Wallpaper 31-ENPress Setup before inserting a disc, or when in stop mode DVD SetupDVD Setup Operation Setting the languagePress Return repeatedly until the Setup mode is deactivated Setting the TV ScreenSetting the Country Code Setting the Rating Level Parental LockAudio output/Optical digital audio output Setting the Digital OutputSetting contents Bitstream / Lpcm 34-ENENT Custom SetupCustom Setup Operation 35-EN36-EN Setup OperationGeneral Setting 37-EN Audio SettingDisplay Setting 38-EN Demo SettingChecking the SAT Radio ID Number Storing Channel PresetsSAT Radio Receiver Optional Receiving Channels with the SAT Radio Receiver OptionalChannel/Category Search Function Setting the Auxiliary Data Field DisplayReceiving Stored Channels Changing the Display41-EN Searching for a desired SongSearching by Playlist Searching by artist name42-EN Quick SearchRandom Play Shuffle M.I.X Searching by album nameEach press changes the display RPT mode is canceled by selecting off43-EN Song will be played back repeatedlyMulti-Changer Selection Optional Changer OptionalControlling CD Changer Optional Playing MP3 Files with the CD Changer Optional45-EN Adjustment Procedure for Dolby Surround46-EN Setting the SpeakersSet MX Mode of the External Audio Processor Over Adjustment= distance of farthest speaker Distance of other speakers Performing Time Correction Manually TCR/ Phase SwitchingCalculating the Time Correction 47-EN48-EN Graphic Equalizer AdjustmentsSwitching the Phase Inputting the Time Correction49-EN Parametric Equalizer AdjustmentsSetting Bass Compressor Speaker Setup50-EN Setting of Dolby DigitalAdjusting the speaker levels Output Level Mixing bass sound to the rear channel Rear MIXBI-PHANTOM ON/OFF Adjusting the DVD LevelAdjusting the acoustic image BI-PHANTOM 51-ENSelecting the Center Width Using the Pro Logic II Mode52-EN 53-EN Storing Settings in the MemoryGetting out the Preset Memory 54-EN Remote ControlControls on Remote Control 55-EN When Using the Remote ControlBattery Replacement 56-EN InformationAbout DVDs Linear PCM audio Lpcm TerminologyDolby Digital Dolby Pro LogicFor details, see List of Language Codes58-EN 59-EN List of Country Codes60-EN CD/MP3/WMA/DVD/Video CD Case of DifficultyBasic RadioPicture is unclear or noisy Indication for CD PlayerIndication for DVD/Video CD Player 62-ENSirius to Indication for SAT Receiver ModeIndication for CD Changer 63-EN64-EN SpecificationsIndication for iPod Mode 65-EN Installation and ConnectionsRemoval Accessory List66-EN Slide the mounting sleeve into the dashboard67-EN Installing the Power Supply UnitWhen mounting with Velcro fasteners 68-EN Connections69-EN Antenna Receptacle Power Antenna Lead BlueConnect the External Monitor System Example70-EN To prevent noise/interference in the audio system 71-ENLimited Warranty Page Page Page
Top Page Image Contents