Kathrein CAP 700 manual They must not be reversed or the unit will not function

Page 21

INSTALLATION AND CONNECTION

LAYING CABLES AND CONNECTING THE TURNTABLE

Lay the coaxial cable to the UFS 740sw.

Lay the turntable power supply cable (3-pin plug) to the battery.

Avoid laying the cables across sharp edges and protect the cables against possible chafing points.

Connect the coaxial cable (coming from the turntable) to the “IF IN” F socket on the rear of the UFS 740sw.

Place the infrared sensor for the receiver close to or directly on top of the TV set and lay the cable to the UFS 740sw. Connect the 6-pin Western connector at the rear to the socket marked “IR REMOTE IN”.

Note: Lay the AV cinch enclosed with the CAP 700 to the Scart cable. Take great care to plug the cables into the correct sockets! The cinch connector must be assigned to the UFS 740sw and the Scart connector to the TV set.

They must not be reversed - or the unit will not function!

CONNECTING TO THE UFS 740SW

Isolate the on-board power supply (master switch “off” or disconnect the positive pole of the on-board power supply battery) before commencing the following work:

Connect the power cable supplied (depending on the power supply available in your motor home or

caravan, either a 12 V supply or a 230 V supply via a power supply unit) to the “” socket on the receiver.

Make sure that the “inline” integrated fuse (5 A) of the cable is fully plugged in and is intact. If the fuse blows, the source of the fault must first be eliminated. The fuse must only ever be replaced by a fuse with the same rating (5 A).

The fuses in the cable and in the receiver may never be bridged – cable fire hazard!

At the connecting point for the power cable, the voltage must not fall below 10.9 V even with a load of 12 A. Otherwise optimum functioning can no longer be guaranteed.

Connect the power cable to the respective socket in your motor home or caravan (12 V or 230 V).

21

Image 21
Contents CAP Contents Foreign Language Installation MANUALS/DISPOSAL Disposal InstructionsSpent batteries are special waste Product Package Mobiset 3 CAP 700 COMPONENTS/SCOPE of DeliveryProper USE USE for the Intended Purpose Proper USESafety Instructions Important Notes Essential informationAdhesive sealant Road Traffic Licensing Regulations StVZO Power supply, fusingChecks before commencing a journey Selecting the Installation Location Installation and ConnectionRequired Tools and Equipment Unpacking and PreparationDirection of travel Ring Adhesive Installation StepsArrow in the direction of travel Recess for cable Adhesive areas between the two grooves Installation of Turntable Direction of travel Version with External Cable Gland FIG. F Brief Instructions for Installing the Turntable Tightening torque 6 Nm Suspended Installation Installation on a Fixed Flat Surface They must not be reversed or the unit will not function Installation and Connection Connection Example for 12 V Battery Connection Reception RANGE/FOOTPRINT Dismantling for Servicing Address of the Service CentreESC DismantlingPolarisation Setting Polarisation SettingAstra Eutelsat Setting Operations Safety NotesView after installation +45 Manual Lowering to Park Position Manual Lowering Dimensions MM Technical DataTechnical Data Type CAP Materials/preparation and company designation Sikaflex 291 Safety Data SheetComposition/data on components Potential hazardsMeasures if inadvertently released Measures for fire fightingHandling and storage Exposure limitation and personal protective equipmentStability and reactivity Physical and chemical characteristicsEcological data Toxicology data SensitisationDisposal instructions Transport dataOther data Sikaflex-291 Ikaflex Sikaflex 291 Technical Data SheetChemical Stability CAP 700 Operating Manual Remote Control Important Information for CAP 700 Before SetupFirst Installation Page Picture format TV aspect ratioTV Scart Output SystemLocal time offset Alignment Satellite Search Moving the Antenna Manually Channel Selection from the Channel List Channel Satellite SelectionChange of LOCATION/TIMER Programming Timer ProgrammingMoving towards Resetting the Turn Table Antenna RESET/PARKINGParking the Turntable System Protection Messages Special Messages from the TurntableSpecial Messages from the Turntable Messages Arising from Software Problems Further Messages Declaration of Conformity For Your Notes 936.3417/-/0908/ZWT Technical data subject to change
Related manuals
Manual 1 pages 14.04 Kb