4.PlaceoneoftheHandrailSpacers(65)ontheright Upright(69)asshown,withthecutouttowardthetread- mill(seeinsetdrawingA).PulltheUprightWireHarness
(98)upthroughtheHandrailSpacerPlacetheother. HandrailSpaceron theleftUpright(notshown).
HaveasecondpersonholdtheHandrails(66)nearthe
Uprights(69)asshown.ConnecttheUprightWire
Harness(98)tothewiresextendingfromtheConsole
Base(81).InserttheconnectorsandtheWireHarness (98)intotheholein theConsoleBase(81)(seeinset drawingB).
65
BeingcarefulnottopinchtheWireHarness(98),setthe Handrails(66)ontheSpacers(65).
5.InserttwoHandrailBushings(75)intotherightUpright (69).TurntheHandrailBushingssotheyfit againstthe
UprightwiththethicksidesoftheBushingsfacingthe centerofthetreadmillasshownin theinsetdrawing.
InserttwoHandrailBolts(78)withHandrailWashers
(77)intotheHandrailBushings(75),therightUpright (69),andtherightHandrailSpacer(65).Lifttheright
Handrail(66)toaligntheBoltswiththeholesin the HandrailNext,threadtheBoltsintotheHandrail.Do.
not tighten the Bolts yet.
Attach the left Handrail (not shown) in the same way. Tighten all four Handrail Bolts (78).
81
_- 77 Thick
,Side
75
7778
6.Make sure that all parts are tightened before you use the treadmill. Note: If there is a thin sheet of clear plastic on the face of the hood decal and the "ComforTrack" decal, remove it. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the floor or car- pet from damage, place a mat under the treadmill.
If you purchase the optional chest pulse sensor (see |
|
|
| 88 | ||
page 24), follow | the steps below to install the receiver |
|
|
| ||
|
| [] |
| |||
included with the chest pulse sensor. |
|
|
|
| ||
1. | Make sure that the power cord is unplugged. Remove |
|
|
|
| |
| the indicated Screws from the Console Back (88). |
|
|
|
| |
| Important: The Screws may be different lengths. Keep |
|
|
|
| |
| track of which Screws were removed from which holes. |
|
|
|
| |
2. | See drawing | 2a. Peel the paper off the pad on the bottom |
|
|
|
|
| of the Receiver (A). Turn the Receiver so the cylinder is |
|
|
|
| |
| on the side shown, and press the Receiver into the bot- | 2a | 81 | 2b | 82 | |
|
|
| ||||
| tom of the Console Base (81) in the indicated location. |
|
|
| / | |
| See drawing 2b. Connect the Short Jumper Wire (B) to |
|
|
| PULSE | |
| the wire on the Receiver (A). Connect the other end of |
|
|
| ||
|
|
|
|
| ||
| the Jumper Wire to the PULSE jack on the back of the |
|
|
|
| |
| Console (82). Note: The included Long Jumper Wire and |
|
|
|
| |
| Wire Tie are not needed and can be discarded. |
|
|
|
| |
| Make sure that no wires are pinched. See step 1 above. |
|
|
|
| |
| Reattach the Console (82) with the Screws. Note: If the |
|
|
|
| |
| Screws are not put in the correct locations, the |
|
|
|
| |
| Console will | be damaged. |
|
|
|
|