Cybex International 710T, LT-14464-4 Rev H manual Activating the Treadmill Follow the steps below

Page 15

Cybex 710T Treadmill Owner’s Manual

turned to the on (I) position and not in use. The control panel will light up and continuously scroll program information when the treadmill is Dormant Mode.

Activating the Treadmill — Follow the steps below:

1.Plug the treadmill power cord into a power outlet from a grounded, dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 50 Hz, and 15 amps, or 208/220 VAC, 60 Hz and 15 amps.

2.Locate the on/off (I/O) power switch on the front end of the treadmill (next to the power cord. Toggle it to the on (I) position to supply power to the internal treadmill components and illuminate the display panel.

3.Mount the treadmill from the rear and place your feet on the two 6” (15 cm) wide side rails located on each side of the running belt.

!CAUTION: Always place your feet on the two 6” (15 cm) wide side rails when starting the treadmill.

4.Press START/ENTER to enter the Select Mode.

5.Upon entering the Select Mode, the display lights to prompt the user to select the appropriate keys. First, the display scrolls “MAXIMUM WORKOUT TIME 55 Min”. Next, the display shows “SELECT MODE: MANUAL - PROGRAM +,” then “MAN- PRG+.” After five seconds, if no key has been pressed, the treadmill will return to the Dormant Mode.

6.Press the - key to select Manual Mode or the + key to select Program Mode.

7.The display shows “SET WEIGHT - or +,” then “- + 160 LB” (73 KG).

Use the - + keys to adjust the weight number displayed to reach your current weight, then press the START/ENTER key to accept your new weight reading. The 710T accepts weights from 40 to 400 lbs. (18 to 181 kg). After five seconds, if no key has been pressed, the treadmill will return to the Dormant Mode. The treadmill uses your weight, speed, and % grade to determine how many calories you burn during a workout.

NOTE: For an accurate calorie count, you must correctly set your weight (including clothing).

8.The display shows “SELECT PROGRAM,” then “Pr1- +” and “FITNESS TEST.” Then it shows a profile of the program followed by “PRESS ENTER TO SELECT, - + TO CHANGE.” The display shows the same cycle of information for each consecutive program until it is interrupted. You may interrupt this cycle at any time by pressing the - + keys to scroll to the program of your choice.

If you select Pr1-Pr5, the display shows “SELECT LEVEL,” then “Lev 1 - +.”

If you selected Pr7, the display shows “SET MAX SPEED - +,” then “SPEED - +.”

Page 3-2

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Cybex 710T Treadmill FCC Compliance Information About This ManualDeclaration of Conformity Table of Contents Page Grounding Instructions Important Voltage InformationImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Press the Stop key once to bring the running belt to a stop Emergency StopPage Specifications Technical SpecificationsPage Quick Operation Guide Detailed Operation GuideSTART/ENTER Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Meaning of terms Data ReadoutsDisplaying Heart Rate Selecting Programs & OptionsUse of Programs P1 Fitness Test Program Manual ModeOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 Program Profile P10 5 Kilometer ProgramP101-P110 Saved Program P11 Demonstration ProgramWorkout Tips Monitoring Your Heart RateTake your heart rate Approx Maximum 85% Heart Rate Age Determine your target heart rateCleaning Your Treadmill Regular Maintenance ActivitiesRunning Belt Maintenance Re-center the belt Re-tension the beltTurn the power off Remove the motor cover and side railsCheck the belt and deck condition Replace the side rails and motor cover Clean under the beltOther Preventive Maintenance Service Schedule Log Sheet Choosing & Preparing a Site Quick SetupItem Qty Description Electrical Power Requirements UnpackingHardware Bags Attach the upright cross brace Assembling the TreadmillMove the base into position Attach the right uprightStar Attach the console to the left uprightAttach the console and left upright to the treadmill Attach the front panel Connect the cablesAttach the motor cover Position the padsConnect Csafe Test the 710T Operation Setting Operation Options Programs On/Off Mode C14Metric/English Measurement Units Pause Time C17 Service Reminders C19Time Limit C15 Speed Limit C16Page Serial Number & Voltage Contacting ServiceWarranty Limited Warranty to NON-CONSUMER BuyersExpiration of Limited Warranties for NON-CONSUMER Buyers Limited Warranty to Consumer BuyersDisclaimer of Warranties and Limitation of Remedies Expiration of Limited Warranties for Consumer BuyersProcedure for Obtaining Warranty Performance Return Material Authorization RMAOrdering Parts Damaged PartsPage Motor Brushes Service InstructionDisconnect the motor cable Turn the power onElevate the treadmill Remove the motor coverSecure the brush caps Secure the brushesSecure the motor cover Clear the error logMotor Current & Voltage Secure the front panelMeasure current draw Measure Motor Voltage at Max Speed, No Load230V Remove the front panelMeasure motor voltage 115VRunning Belt & Deck Secure the side rails and motor coverRemove the side rails Remove the rear roller Loosen the deckLoosen the drive belt Front Roller Drive BeltAttach the running deck Attach the drive belt tensioning assemblyReinstall the side rails and end caps Rear RollerError 1 No Speed Signal at Startup Error CodesError 2 Excessive Current Draw Error 3 Loss of Speed SignalError 50 Overspeed Error 70 Loss of Novram Information Diagnostic TestsC1 Program Revision Level C18 Power Relay Tests C19 Service RemindersC5 Overlay Test C2 Actual SpeedC3 Current Draw C4 LED TestC6 Csafe Port Check C7 Tone Generator CheckC8 Speed Sensor Count C11 Total Hours C12 Error LOGC9 Incline Sensor C10 Total MileageC15 Time Limit C18 Power Relay TestC19 Service Reminders C14 PGM LockoutService QTY Description Parts ListQTY Description NS = Not Shown Page Based on SC-710T Rev E

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents