Cybex International LT-14464-4 Rev H, 710T manual Secure the brushes, Secure the brush caps

Page 66
.438" (7/16") (11.13 mm)
Replace OK
Figure 2

Cybex 710T Treadmill Owner’s Manual

 

 

Front

 

 

Panel

 

 

!WARNING: Avoid Touching

-

+

R34 and Black Capacitors

 

Motor

 

 

Cable

 

 

Figure 1

be pitted or blackened on one edge. Too many of these indicate a worn commutator, and the motor should be replaced. The commutator may be cleaned with narrow commutator stone if carbon build-up is present. (File down the stone if it won’t fit in the brush holder hole.) Brush dust can be loosened from the brush holder area by lightly filing the surfaces. Dirt and brush dust inside the drive motor can cause a short and should be vacuumed out of the motor.

B. Inspect the brushes for signs of excessive wear or cracks. The motor brushes must be replaced if one or both is worn to .438” (7/16"/11.13mm) or less in length, is broken or chipped, has a broken spring, or binds in the motor. See Figure 2.

8. Secure the brushes.

A. Slide the brushes (new or original) into the motor brush holders. If the new brush does not slide in

easily, the edges or corners of the brush can be lightly filed down. If cleaning the motor, (see step 6A), and filing the brush doesn't allow the brush to slide easily in the brush holder, the motor should be replaced.

NOTE: The motor may make a clicking noise as new brushes wear in. If you reinstall the original brushes it is good to install them facing their original position. Reversing the orientation of the brush can cause a clicking noise during operation until the brushes wear in.

9.Secure the brush caps.

A.Place each brush in its brush holder and carefully push the spring in while screwing on the brush cap. If the brush cap is damaged, order Cybex replacement part number HX-10300-2.

7Service

Service Instruction . . . . . . . . 7-1 Motor Brushes. . . . . . . . . . . 7-1

Motor Current & Voltage . . . 7-4

Running Belt & Deck . . . . . . 7-7

Drive Belt . . . . . . . . . . . . . . . 7-9

Front Roller . . . . . . . . . . . . . 7-9

Rear Roller . . . . . . . . . . . . 7-10

Error Codes . . . . . . . . . . . . 7-11

Diagnostic Tests . . . . . . . . 7-13

Parts List . . . . . . . . . . . . . . 7-20

Exploded View . . . . . . . . . . 7-23

710T Schematic . . . . . . . . . 7-24

Page 7-3

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Cybex 710T Treadmill About This Manual FCC Compliance InformationDeclaration of Conformity Table of Contents Page Important Voltage Information Grounding InstructionsImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Emergency Stop Press the Stop key once to bring the running belt to a stopPage Technical Specifications SpecificationsPage Quick Operation Guide Detailed Operation GuideSTART/ENTER Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Data Readouts Meaning of termsSelecting Programs & Options Displaying Heart RateUse of Programs Manual Mode P1 Fitness Test ProgramOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 5 Kilometer Program P10 Program ProfileP11 Demonstration Program P101-P110 Saved ProgramWorkout Tips Monitoring Your Heart RateTake your heart rate Determine your target heart rate Approx Maximum 85% Heart Rate AgeRegular Maintenance Activities Cleaning Your TreadmillRunning Belt Maintenance Re-tension the belt Re-center the beltTurn the power off Remove the motor cover and side railsCheck the belt and deck condition Clean under the belt Replace the side rails and motor coverOther Preventive Maintenance Service Schedule Log Sheet Quick Setup Choosing & Preparing a SiteItem Qty Description Electrical Power Requirements UnpackingHardware Bags Attach the right upright Assembling the TreadmillMove the base into position Attach the upright cross braceAttach the console to the left upright StarAttach the console and left upright to the treadmill Connect the cables Attach the front panelAttach the motor cover Position the padsConnect Csafe Test the 710T Operation Setting Operation Options Programs On/Off Mode C14Metric/English Measurement Units Speed Limit C16 Service Reminders C19Time Limit C15 Pause Time C17Page Limited Warranty to NON-CONSUMER Buyers Contacting ServiceWarranty Serial Number & VoltageLimited Warranty to Consumer Buyers Expiration of Limited Warranties for NON-CONSUMER BuyersExpiration of Limited Warranties for Consumer Buyers Disclaimer of Warranties and Limitation of RemediesReturn Material Authorization RMA Procedure for Obtaining Warranty PerformanceDamaged Parts Ordering PartsPage Service Instruction Motor BrushesRemove the motor cover Turn the power onElevate the treadmill Disconnect the motor cableSecure the brushes Secure the brush capsSecure the front panel Clear the error logMotor Current & Voltage Secure the motor coverMeasure Motor Voltage at Max Speed, No Load Measure current draw115V Remove the front panelMeasure motor voltage 230VRunning Belt & Deck Secure the side rails and motor coverRemove the side rails Remove the rear roller Loosen the deckLoosen the drive belt Drive Belt Front RollerRear Roller Attach the drive belt tensioning assemblyReinstall the side rails and end caps Attach the running deckError Codes Error 1 No Speed Signal at StartupError 2 Excessive Current Draw Error 3 Loss of Speed SignalError 50 Overspeed Diagnostic Tests Error 70 Loss of Novram InformationC18 Power Relay Tests C19 Service Reminders C1 Program Revision LevelC4 LED Test C2 Actual SpeedC3 Current Draw C5 Overlay TestC6 Csafe Port Check C7 Tone Generator CheckC8 Speed Sensor Count C10 Total Mileage C12 Error LOGC9 Incline Sensor C11 Total HoursC14 PGM Lockout C18 Power Relay TestC19 Service Reminders C15 Time LimitService Parts List QTY DescriptionQTY Description NS = Not Shown Page Based on SC-710T Rev E

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents