Cybex International 710T manual Setting Operation Options, Metric/English Measurement Units

Page 55

Cybex 710T Treadmill Owner’s Manual

9.Run the treadmill through its full % grade range. Press and hold the INCLINE ^ key until the treadmill reaches its highest grade (15%). Then press the INCLINE v key until the

treadmill is back to 0% grade.

10.Press STOP three times to stop the running belt, end the checkout session, and return the display to Dormant Mode.

Finish your setup of the 710T by setting the operation options as desired.

Setting Operation Options

The 710T allows you to configure the following features:

1.Metric/English Measurement Units

2.Programs On/Off Mode

3.Time Limit

4.Speed Limit

5.Pause Time

6.Service Reminders

1.Metric/English Measurement Units

You can change the settings to metric units, or back to English units. With the treadmill in the on (I) position and in Dormant Mode, press and hold the STOP and + buttons at the same time for two seconds. The display will show “METRIC”. To change to English, press and hold the STOP and - keys at the same time for two seconds and the display will show “ENGLISH”.

NOTE: The next four features can be changed after entering Diagnostic Tests. To enter Diagnostic Tests, press and hold SCAN/SAVE, then press -.

2. Programs On/Off Mode (C14)

The programs on/off mode can be used to prevent or “lock out” the use of the 710T's programs, for Manual Mode use only.

To enter Diagnostic Tests, press and hold SCAN/SAVE, then press -. You will see the message “DIAGNOSTIC TESTS”. Press v or ^ or to scroll to ”C14 PGM LOCKOUT”. Press the

+key to turn the lockout feature on, disabling all programs. Press the - key to turn the lockout features off enabling all programs. Press START/ENTER to confirm, and again to save. Press ^ to scroll to C15.

Page 5-10

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Cybex 710T Treadmill FCC Compliance Information About This ManualDeclaration of Conformity Table of Contents Page Grounding Instructions Important Voltage InformationImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Press the Stop key once to bring the running belt to a stop Emergency StopPage Specifications Technical SpecificationsPage Detailed Operation Guide Quick Operation GuideSTART/ENTER Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Meaning of terms Data ReadoutsDisplaying Heart Rate Selecting Programs & OptionsUse of Programs P1 Fitness Test Program Manual ModeOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 Program Profile P10 5 Kilometer ProgramP101-P110 Saved Program P11 Demonstration ProgramMonitoring Your Heart Rate Workout TipsTake your heart rate Approx Maximum 85% Heart Rate Age Determine your target heart rateCleaning Your Treadmill Regular Maintenance ActivitiesRunning Belt Maintenance Re-center the belt Re-tension the beltRemove the motor cover and side rails Turn the power offCheck the belt and deck condition Replace the side rails and motor cover Clean under the beltOther Preventive Maintenance Service Schedule Log Sheet Choosing & Preparing a Site Quick SetupItem Qty Description Unpacking Electrical Power RequirementsHardware Bags Attach the upright cross brace Assembling the TreadmillMove the base into position Attach the right uprightStar Attach the console to the left uprightAttach the console and left upright to the treadmill Attach the front panel Connect the cablesPosition the pads Attach the motor coverConnect Csafe Test the 710T Operation Programs On/Off Mode C14 Setting Operation OptionsMetric/English Measurement Units Pause Time C17 Service Reminders C19Time Limit C15 Speed Limit C16Page Serial Number & Voltage Contacting ServiceWarranty Limited Warranty to NON-CONSUMER BuyersExpiration of Limited Warranties for NON-CONSUMER Buyers Limited Warranty to Consumer BuyersDisclaimer of Warranties and Limitation of Remedies Expiration of Limited Warranties for Consumer BuyersProcedure for Obtaining Warranty Performance Return Material Authorization RMAOrdering Parts Damaged PartsPage Motor Brushes Service InstructionDisconnect the motor cable Turn the power onElevate the treadmill Remove the motor coverSecure the brush caps Secure the brushesSecure the motor cover Clear the error logMotor Current & Voltage Secure the front panelMeasure current draw Measure Motor Voltage at Max Speed, No Load230V Remove the front panelMeasure motor voltage 115VSecure the side rails and motor cover Running Belt & DeckRemove the side rails Loosen the deck Remove the rear rollerLoosen the drive belt Front Roller Drive BeltAttach the running deck Attach the drive belt tensioning assemblyReinstall the side rails and end caps Rear RollerError 1 No Speed Signal at Startup Error CodesError 3 Loss of Speed Signal Error 2 Excessive Current DrawError 50 Overspeed Error 70 Loss of Novram Information Diagnostic TestsC1 Program Revision Level C18 Power Relay Tests C19 Service RemindersC5 Overlay Test C2 Actual SpeedC3 Current Draw C4 LED TestC7 Tone Generator Check C6 Csafe Port CheckC8 Speed Sensor Count C11 Total Hours C12 Error LOGC9 Incline Sensor C10 Total MileageC15 Time Limit C18 Power Relay TestC19 Service Reminders C14 PGM LockoutService QTY Description Parts ListQTY Description NS = Not Shown Page Based on SC-710T Rev E

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents