Cybex International 710T, LT-14464-4 Rev H manual Running Belt Maintenance

Page 39

Cybex 710T Treadmill Owner’s Manual

To clean the motor components, you must remove the two Phillips head screws that hold the motor cover in place. Lift the cover, and put it and the screws aside. Use a vacuum attachment or hand vacuum to clean the exposed elevation assembly, drive motor, lower electronics and the surrounding areas.

Also use a dry cloth for the areas that you can't reach with the vacuum cleaner. If the machine has not been used for some time or is excessively dirty, use a dry cloth to wipe all exposed areas. Replace the cover and screws when finished.

With the help of another person, lift the rear of the treadmill and roll it back from its present position so as to vacuum the floor area underneath the unit. Wipe clean the underside of the 710T to prevent dirt and dust build-up. When finished, return the treadmill to its normal position.

Contact Heart Rate Grips — Contaminants, such as hand lotions, oils or body powder, may come off on the contact heart rate grips. These can reduce sensitivity and interfere with the heart rate signal. It is recommended that the user have clean hands when using the contact heart rate. Clean the grips using a cloth dampened with a cleaning solution containing alcohol. The grips are the only part of the treadmill you should use a cleaning solution containing alcohol.

In addition, the nickel plating on the 710T may become tarnished and blackened with time. This may reduce sensitivity and interfere with the heart rate signal. Use an emery cloth to remove the tarnish from the exposed nickel plating on the heart rate grips.

Running Belt Maintenance

Belt and Deck — Clean the belt and the deck surfaces to minimize the effect of friction between the wood deck and the running belt. Clean the underside of the running belt and the top of the running deck surface by wiping them with a clean dry towel. This should be done often to prevent premature wear of the deck, running belt, and the drive motor system. See the Service Schedule in this chapter to determine the minimum recommended cleaning.

The running belt may become loose and slip on the drive roller with each foot plant. The 710T is equipped with visual indicators of belt tension. These are located at the rear of the treadmill where the two 3/4" bolts protrude from the plastic end caps. See Figure 1. These are designed to indicate if the running belt is at the proper tension to insure safe operation of the unit. If the belt has become loose, the silver colored washer located under the bolt will move out slightly from the protruding tab molded in the end cap. See the Service Schedule in this chapter to determine the minimum recommended checking of the belt tension.

Page 4-2

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Cybex 710T Treadmill FCC Compliance Information About This ManualDeclaration of Conformity Table of Contents Page Grounding Instructions Important Voltage InformationImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Press the Stop key once to bring the running belt to a stop Emergency StopPage Specifications Technical SpecificationsPage Quick Operation Guide Detailed Operation GuideSTART/ENTER Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Meaning of terms Data ReadoutsDisplaying Heart Rate Selecting Programs & OptionsUse of Programs P1 Fitness Test Program Manual ModeOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 Program Profile P10 5 Kilometer ProgramP101-P110 Saved Program P11 Demonstration ProgramWorkout Tips Monitoring Your Heart RateTake your heart rate Approx Maximum 85% Heart Rate Age Determine your target heart rateCleaning Your Treadmill Regular Maintenance ActivitiesRunning Belt Maintenance Re-center the belt Re-tension the beltTurn the power off Remove the motor cover and side railsCheck the belt and deck condition Replace the side rails and motor cover Clean under the beltOther Preventive Maintenance Service Schedule Log Sheet Choosing & Preparing a Site Quick SetupItem Qty Description Electrical Power Requirements UnpackingHardware Bags Attach the upright cross brace Assembling the TreadmillMove the base into position Attach the right uprightStar Attach the console to the left uprightAttach the console and left upright to the treadmill Attach the front panel Connect the cablesAttach the motor cover Position the padsConnect Csafe Test the 710T Operation Setting Operation Options Programs On/Off Mode C14Metric/English Measurement Units Pause Time C17 Service Reminders C19Time Limit C15 Speed Limit C16Page Serial Number & Voltage Contacting ServiceWarranty Limited Warranty to NON-CONSUMER BuyersExpiration of Limited Warranties for NON-CONSUMER Buyers Limited Warranty to Consumer BuyersDisclaimer of Warranties and Limitation of Remedies Expiration of Limited Warranties for Consumer BuyersProcedure for Obtaining Warranty Performance Return Material Authorization RMAOrdering Parts Damaged PartsPage Motor Brushes Service InstructionDisconnect the motor cable Turn the power onElevate the treadmill Remove the motor coverSecure the brush caps Secure the brushesSecure the motor cover Clear the error logMotor Current & Voltage Secure the front panelMeasure current draw Measure Motor Voltage at Max Speed, No Load230V Remove the front panelMeasure motor voltage 115VRunning Belt & Deck Secure the side rails and motor coverRemove the side rails Remove the rear roller Loosen the deckLoosen the drive belt Front Roller Drive BeltAttach the running deck Attach the drive belt tensioning assemblyReinstall the side rails and end caps Rear RollerError 1 No Speed Signal at Startup Error CodesError 2 Excessive Current Draw Error 3 Loss of Speed SignalError 50 Overspeed Error 70 Loss of Novram Information Diagnostic TestsC1 Program Revision Level C18 Power Relay Tests C19 Service RemindersC5 Overlay Test C2 Actual SpeedC3 Current Draw C4 LED TestC6 Csafe Port Check C7 Tone Generator CheckC8 Speed Sensor Count C11 Total Hours C12 Error LOGC9 Incline Sensor C10 Total MileageC15 Time Limit C18 Power Relay TestC19 Service Reminders C14 PGM LockoutService QTY Description Parts ListQTY Description NS = Not Shown Page Based on SC-710T Rev E

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents