Cybex International 710T, LT-14464-4 Rev H Rear Roller, Attach the drive belt tensioning assembly

Page 73

Cybex 710T Treadmill Owner’s Manual

12.Attach the drive belt tensioning assembly.

A.Place the drive belt tensioning roller in position under the front bracket on the drive belt tensioning assembly. See Figure 3.

B.Place the two steel bar springs over the drive belt tensioning roller plate and under the front bracket on the drive belt tensioning assembly. Be sure springs are firmly seated against the stop under the drive belt retainer.

C.Be sure that the pulley is aligned with the drive belt.

D.Using a 1/2” wrench, tighten the mounting bolt and two washers while keeping the pulley aligned with the drive belt. NOTE: A drive belt that is too loose may squeal and you may be able to see it slip when you walk on the running belt.

13.Attach the running deck.

A.Using an Allen wrench, attach the remaining screw, spacer, and belt retaining washer in the frontmost right hole.

B.Using a 7/16” wrench, attach the nine screws, nine washers and nine belt retaining washers that hold the deck in place. See Figure 3.

Rear Roller

14.Replace the rear roller.

A.Slide the rear roller into the running belt.

B.Place the bolts, washers, springs, and nuts in position. Partially tighten the two bolts leaving them loose until step 15C.

15.Reinstall the side rails and end caps.

A.Line up the side rails with the end of the frame. Place the bottom edge of each side rail under the treadmill frame and push the top edge of each side rail in place. It will snap on.

B.Place the end cap flush with the end of the side rail and the end of the frame. Use a 3/16” Allen wrench to attach the two button head screws that fasten each end cap and side rail to the frame.

C.Using a 3/4” wrench, tighten each rear roller bolt evenly, making sure not to loosen either bolt too many turns before moving to the other bolt. use the small plastic tab above the bolt hole as a visual reference to tension the rear roller bolts. When tightening the rear roller bolts, look down onto the plastic tab located just above the bolt head. Make sure the entire side of the silver washer is visible and is not hidden by any portion of the tab.

16.Adjust the running belt tension and center the belt by following the instructions

Page 7-10

Image 73

Contents Cybex 710T Treadmill FCC Compliance Information About This ManualDeclaration of Conformity Table of Contents Page Grounding Instructions Important Voltage InformationImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Press the Stop key once to bring the running belt to a stop Emergency StopPage Specifications Technical SpecificationsPage Detailed Operation Guide Quick Operation GuideSTART/ENTER Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Meaning of terms Data ReadoutsDisplaying Heart Rate Selecting Programs & OptionsUse of Programs P1 Fitness Test Program Manual ModeOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 Program Profile P10 5 Kilometer ProgramP101-P110 Saved Program P11 Demonstration ProgramMonitoring Your Heart Rate Workout TipsTake your heart rate Approx Maximum 85% Heart Rate Age Determine your target heart rateCleaning Your Treadmill Regular Maintenance ActivitiesRunning Belt Maintenance Re-center the belt Re-tension the beltRemove the motor cover and side rails Turn the power offCheck the belt and deck condition Replace the side rails and motor cover Clean under the beltOther Preventive Maintenance Service Schedule Log Sheet Choosing & Preparing a Site Quick SetupItem Qty Description Unpacking Electrical Power RequirementsHardware Bags Move the base into position Assembling the TreadmillAttach the right upright Attach the upright cross braceStar Attach the console to the left uprightAttach the console and left upright to the treadmill Attach the front panel Connect the cablesPosition the pads Attach the motor coverConnect Csafe Test the 710T Operation Programs On/Off Mode C14 Setting Operation OptionsMetric/English Measurement Units Time Limit C15 Service Reminders C19Speed Limit C16 Pause Time C17Page Warranty Contacting ServiceLimited Warranty to NON-CONSUMER Buyers Serial Number & VoltageExpiration of Limited Warranties for NON-CONSUMER Buyers Limited Warranty to Consumer BuyersDisclaimer of Warranties and Limitation of Remedies Expiration of Limited Warranties for Consumer BuyersProcedure for Obtaining Warranty Performance Return Material Authorization RMAOrdering Parts Damaged PartsPage Motor Brushes Service InstructionElevate the treadmill Turn the power onRemove the motor cover Disconnect the motor cableSecure the brush caps Secure the brushesMotor Current & Voltage Clear the error logSecure the front panel Secure the motor coverMeasure current draw Measure Motor Voltage at Max Speed, No LoadMeasure motor voltage Remove the front panel115V 230V Secure the side rails and motor cover Running Belt & Deck Remove the side rails Loosen the deck Remove the rear rollerLoosen the drive belt Front Roller Drive BeltReinstall the side rails and end caps Attach the drive belt tensioning assemblyRear Roller Attach the running deckError 1 No Speed Signal at Startup Error CodesError 3 Loss of Speed Signal Error 2 Excessive Current DrawError 50 Overspeed Error 70 Loss of Novram Information Diagnostic TestsC1 Program Revision Level C18 Power Relay Tests C19 Service RemindersC3 Current Draw C2 Actual SpeedC4 LED Test C5 Overlay TestC7 Tone Generator Check C6 Csafe Port CheckC8 Speed Sensor Count C9 Incline Sensor C12 Error LOGC10 Total Mileage C11 Total HoursC19 Service Reminders C18 Power Relay TestC14 PGM Lockout C15 Time LimitService QTY Description Parts ListQTY Description NS = Not Shown Page Based on SC-710T Rev E