Cybex International 710T, LT-14464-4 Rev H manual Control During Operation

Page 17

Cybex 710T Treadmill Owner’s Manual

same incline, speed and time where you left off. If no key has been pressed during the five minute pause,workout data will be cleared, the display will change to Dormant Mode.

Press the STOP key a second time to begin a workout review. The totals reached during your workout session will cycle and the five minute pause will end. After the workout review is finished the treadmill will automatically change to Dormant Mode.

Press the STOP key a third time to interrupt workout data from cycling and to change the display to Dormant Mode.

NOTE: A set-up feature, (see Diagnostic Test C17 in the Service chapter), allows you to reduce the pause time to ten seconds.

The function of the immobilization method: The purpose of immobilizing the treadmill is to prevent unauthorized use. This can be accomplished by removing the power cord from the outlet and from the treadmill.

The emergency dismount: Should you experience pain, feel faint, or need to stop your treadmill in an emergency situation, you should follow these steps:

1.Grip handrails for support.

2.Step onto the side rails.

3.Press the STOP button two times.

The function of the emergency stop: The red STOP button functions as the emergency stop. In an emergency situation, press the STOP button once and the treadmill will come to a stop. If you are ending your workout session, press STOP a second time, so that the next user will not resume at the last user’s speed and elevation.

Control During Operation

Every key on the display is usable during operation. Any key may be pressed at any time to make adjustments in speed, elevation, level, or data readouts.

Changing Speed — Press the - + keys to change the speed in increments of 0.1 mph or 0.10 kph. Minimum to maximum speed is from 1.0 - 10 mph (1.6 - 16 kph).

Changing Incline — Press the v^ arrows to change the elevation in increments of 1%. Maximum elevation is 15%. (Elevation is defined as the ratio of rise over run of the treadmill deck.)

Changing Level — During a programmed workout, press the START/ENTER key to display the current program and level status. Then press v^ arrows to change the level. The level will change immediately and will continue to accumulate performance data without interruption. For information on determining which level is right for you, see P1 — Fitness Test in this chapter.

Page 3-4

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Cybex 710T Treadmill FCC Compliance Information About This ManualDeclaration of Conformity Table of Contents Page Grounding Instructions Important Voltage InformationImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Press the Stop key once to bring the running belt to a stop Emergency StopPage Specifications Technical SpecificationsPage START/ENTER Quick Operation GuideDetailed Operation Guide Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Meaning of terms Data ReadoutsDisplaying Heart Rate Selecting Programs & OptionsUse of Programs P1 Fitness Test Program Manual ModeOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 Program Profile P10 5 Kilometer ProgramP101-P110 Saved Program P11 Demonstration ProgramTake your heart rate Workout TipsMonitoring Your Heart Rate Approx Maximum 85% Heart Rate Age Determine your target heart rateCleaning Your Treadmill Regular Maintenance ActivitiesRunning Belt Maintenance Re-center the belt Re-tension the beltCheck the belt and deck condition Turn the power offRemove the motor cover and side rails Replace the side rails and motor cover Clean under the beltOther Preventive Maintenance Service Schedule Log Sheet Choosing & Preparing a Site Quick SetupItem Qty Description Hardware Bags Electrical Power RequirementsUnpacking Move the base into position Assembling the TreadmillAttach the right upright Attach the upright cross braceStar Attach the console to the left uprightAttach the console and left upright to the treadmill Attach the front panel Connect the cablesConnect Csafe Attach the motor coverPosition the pads Test the 710T Operation Metric/English Measurement Units Setting Operation OptionsPrograms On/Off Mode C14 Time Limit C15 Service Reminders C19Speed Limit C16 Pause Time C17Page Warranty Contacting ServiceLimited Warranty to NON-CONSUMER Buyers Serial Number & VoltageExpiration of Limited Warranties for NON-CONSUMER Buyers Limited Warranty to Consumer BuyersDisclaimer of Warranties and Limitation of Remedies Expiration of Limited Warranties for Consumer BuyersProcedure for Obtaining Warranty Performance Return Material Authorization RMAOrdering Parts Damaged PartsPage Motor Brushes Service InstructionElevate the treadmill Turn the power onRemove the motor cover Disconnect the motor cableSecure the brush caps Secure the brushesMotor Current & Voltage Clear the error logSecure the front panel Secure the motor coverMeasure current draw Measure Motor Voltage at Max Speed, No LoadMeasure motor voltage Remove the front panel115V 230VRemove the side rails Running Belt & DeckSecure the side rails and motor cover Loosen the drive belt Remove the rear rollerLoosen the deck Front Roller Drive BeltReinstall the side rails and end caps Attach the drive belt tensioning assemblyRear Roller Attach the running deckError 1 No Speed Signal at Startup Error CodesError 50 Overspeed Error 2 Excessive Current DrawError 3 Loss of Speed Signal Error 70 Loss of Novram Information Diagnostic TestsC1 Program Revision Level C18 Power Relay Tests C19 Service RemindersC3 Current Draw C2 Actual SpeedC4 LED Test C5 Overlay TestC8 Speed Sensor Count C6 Csafe Port CheckC7 Tone Generator Check C9 Incline Sensor C12 Error LOGC10 Total Mileage C11 Total HoursC19 Service Reminders C18 Power Relay TestC14 PGM Lockout C15 Time LimitService QTY Description Parts ListQTY Description NS = Not Shown Page Based on SC-710T Rev E

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents