Cybex International 710T manual Turn the power on, Elevate the treadmill, Remove the motor cover

Page 65

Cybex 710T Treadmill Owner’s Manual

!WARNING: Keep wet items away from inside parts of the treadmill. Electrical shock could occur even if the treadmill is unplugged.

1.Turn the power on.

A.With the power cord plugged in turn the main power switch to the on (I) position.

2.Elevate the treadmill.

A.Without standing on the belt, press the START/ENTER key and begin running the treadmill.

B.Press the ^ arrow and elevate the treadmill fully.

3.Turn the power off.

A.While the treadmill is still fully elevated and running turn the main power switch to the off (O) position.

B.Unplug the treadmill from the power outlet.

4.Remove the motor cover.

A.Remove the screws that fasten the motor cover to the frame.

B.Lift the cover and remove it from the treadmill. Set the cover and screws aside.

5.Disconnect the motor cable.

A.Using a 3/16” Allen wrench, remove the four button head screws and four starwashers that hold the front panel in position.

B.Place the front panel on the floor or temporarily screw two of the button head screws into the frame where they came out, and then hang the front panel on the screws.

C.Avoid touching R34 and the black capacitors. Disconnect the motor cable. See Figure 1.

6.Remove the brush caps.

A.Using a large flat head screwdriver unscrew the two brush caps on the drive motor. The brushes should spring out. The lower brush cap may be difficult to remove with a long screwdriver. If you need a brush cap tool, order Cybex part number FS-12263.

NOTE: If the brush doesn’t spring out, you can use a small screwdriver or needle nose pliers to pry up the base of the brush spring. If the brush spring is broken, ensure no loose parts are left behind.

7.Examine the brushes and commutator.

A.Inspect the commutator by looking through the top brush holder into the motor. Slowly spin the motor by turning the flywheel. Look for noticeable damage and for signs of wear such as arcing, pitting, burning, or uneven wear. Commutator bars that are 'dirty penny' brownish copper are in great condition. However, some commutator bars may

Page 7-2

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Cybex 710T Treadmill FCC Compliance Information About This ManualDeclaration of Conformity Table of Contents Page Grounding Instructions Important Voltage InformationImportant Safety Instructions Important Safety Instructions Emergency Stop Risk of Personal Press the Stop key once to bring the running belt to a stop Emergency StopPage Specifications Technical SpecificationsPage START/ENTER Quick Operation GuideDetailed Operation Guide Activating the Treadmill Follow the steps below Stopping the Treadmill Control During Operation Meaning of terms Data ReadoutsDisplaying Heart Rate Selecting Programs & OptionsUse of Programs P1 Fitness Test Program Manual ModeOperation P2 Weight Loss Program P2 Program Profile P3 Cardiovascular Program Operation P4 Speed Challenge Program Operation P5 Express Program P6 Hill Interval Program P7 Speed Interval Program P8 Pikes Peak Program P9 River Run Program P10 Program Profile P10 5 Kilometer ProgramP101-P110 Saved Program P11 Demonstration ProgramTake your heart rate Workout TipsMonitoring Your Heart Rate Approx Maximum 85% Heart Rate Age Determine your target heart rateCleaning Your Treadmill Regular Maintenance ActivitiesRunning Belt Maintenance Re-center the belt Re-tension the beltCheck the belt and deck condition Turn the power offRemove the motor cover and side rails Replace the side rails and motor cover Clean under the beltOther Preventive Maintenance Service Schedule Log Sheet Choosing & Preparing a Site Quick SetupItem Qty Description Hardware Bags Electrical Power RequirementsUnpacking Move the base into position Assembling the TreadmillAttach the right upright Attach the upright cross braceStar Attach the console to the left uprightAttach the console and left upright to the treadmill Attach the front panel Connect the cablesConnect Csafe Attach the motor coverPosition the pads Test the 710T Operation Metric/English Measurement Units Setting Operation OptionsPrograms On/Off Mode C14 Time Limit C15 Service Reminders C19Speed Limit C16 Pause Time C17Page Warranty Contacting ServiceLimited Warranty to NON-CONSUMER Buyers Serial Number & VoltageExpiration of Limited Warranties for NON-CONSUMER Buyers Limited Warranty to Consumer BuyersDisclaimer of Warranties and Limitation of Remedies Expiration of Limited Warranties for Consumer BuyersProcedure for Obtaining Warranty Performance Return Material Authorization RMAOrdering Parts Damaged PartsPage Motor Brushes Service InstructionElevate the treadmill Turn the power onRemove the motor cover Disconnect the motor cableSecure the brush caps Secure the brushesMotor Current & Voltage Clear the error logSecure the front panel Secure the motor coverMeasure current draw Measure Motor Voltage at Max Speed, No LoadMeasure motor voltage Remove the front panel115V 230VRemove the side rails Running Belt & DeckSecure the side rails and motor cover Loosen the drive belt Remove the rear rollerLoosen the deck Front Roller Drive BeltReinstall the side rails and end caps Attach the drive belt tensioning assemblyRear Roller Attach the running deckError 1 No Speed Signal at Startup Error CodesError 50 Overspeed Error 2 Excessive Current DrawError 3 Loss of Speed Signal Error 70 Loss of Novram Information Diagnostic TestsC1 Program Revision Level C18 Power Relay Tests C19 Service RemindersC3 Current Draw C2 Actual SpeedC4 LED Test C5 Overlay TestC8 Speed Sensor Count C6 Csafe Port CheckC7 Tone Generator Check C9 Incline Sensor C12 Error LOGC10 Total Mileage C11 Total HoursC19 Service Reminders C18 Power Relay TestC14 PGM Lockout C15 Time LimitService QTY Description Parts ListQTY Description NS = Not Shown Page Based on SC-710T Rev E

LT-14464-4 Rev H, 710T specifications

The Cybex International 710T, LT-14464-4 Rev H is a top-tier piece of fitness equipment designed for commercial gym settings and serious home workout enthusiasts. This high-performance treadmill stands out due to its innovative features, robust design, and technology that prioritizes user comfort and efficiency.

One of the central features of the 710T is its advanced mechanics, which include a powerful DC motor that provides a smooth and consistent performance across various speeds. With a top speed of 12 miles per hour and an incline of up to 15%, users can engage in a diverse range of workouts that simulate outdoor running and walking environments. This versatility makes the 710T suitable for users of different fitness levels, from beginners to seasoned athletes.

The treadmill also boasts a spacious running surface of 22 inches by 60 inches, allowing for comfortable strides and reduced risk of injury. The patented FlexTech® system is engineered to absorb impact, providing a cushioned deck that minimizes stress on joints while still allowing for an effective workout. This technology promotes longer exercise sessions, which can contribute to better overall fitness goals.

Another remarkable feature is the intuitive console equipped with a large, easy-to-read display that offers users essential metrics, including time, distance, calories burned, and heart rate. The console is designed for simplicity and ease of use, with quick-access buttons for speed and incline adjustments, enabling users to customize their workouts effortlessly.

Connectivity is a significant aspect of modern workout experiences, and the 710T does not disappoint. It includes built-in Bluetooth compatibility, allowing users to sync their devices with fitness apps for tracking and sharing workout progress. Additionally, the integrated USB charging port ensures devices remain powered during exercise, allowing for uninterrupted music or entertainment.

Safety is a top priority, and the Cybex 710T is equipped with emergency stop features and adjustable handrails for added stability. The durable construction of the treadmill makes it suitable for heavy daily use, ensuring longevity and reliability.

In summary, the Cybex International 710T, LT-14464-4 Rev H is a comprehensive treadmill engineered with innovative technology, robust design, and user-friendly features that cater to various fitness needs. Its combination of performance, safety, and connectivity epitomizes the philosophy of Cybex in promoting an efficient and enjoyable workout experience.
Top Page Image Contents