Healthrider HCTL05910 manual TROUBLE-SHOOTING and Maintenance, Problemsolution, Unplug, Power Cord

Page 22

TROUBLE-SHOOTING AND MAINTENANCE

Most treadmill problems can be solved by following the instructions below. If further assistance is needed, please call our Customer Service Department toll-free at 1-888-936-4266, Monday through Friday, 8h00 to 18h30, Eastern Standard Time (excluding holidays).

PROBLEMSOLUTION

1.The power does not turn on

a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page 7.) Use only a CUL-listed surge protector, rated

at 15 amps, with a 14-gauge cord of 1,5 m (5 ft.) or less in length. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in.

d. Check the on/off switch located on the treadmill near the power cord. The switch must be in the on position.

c

Tripped Reset

d

On

Position

2.The power turns off during use

a.Check the circuit breaker located on the treadmill frame near the power cord (see

1. c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b.Make sure that the power cord is plugged in.

c.Remove the key from the console and then reinsert it.

d.Make sure that the on/off switch is in the on position (see 1. d. above).

3. The walking belt

a. Make sure that only an appropriate surge suppressor is used (see 1. a. above).

slows when walked

 

 

 

on

b. If the walking belt is overtightened, tread-

b

 

mill performance may decrease and the

 

 

 

walking belt may become damaged.

3–4”

 

Remove the key and

UNPLUG THE

 

 

 

POWER CORD

. Using the allen wrench,

 

 

turn both rear roller adjustment bolts

 

 

counterclockwise, 1/4 of a turn. When the

 

 

walking belt is properly tightened, you

 

 

should be able to lift each side of the

Rear Roller Adjustment Bolts

 

walking belt 3 to 4 inches off the walking

 

 

platform. Be careful to keep the walking

 

 

belt centered. Plug in the power cord, insert the key and run the treadmill for a few

 

minutes. Repeat until the walking belt is properly tightened.

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model No. HCTL05910 Serial No QUESTIONS?Serial Number Decal Table of Contents Wear appropriate exercise clothing when Important PrecautionsUsing hand weights and not holding Use only a CUL-listed surge protector, rated atPage Back Before YOU BeginRight Side With the help of a second person,carefully raise AssemblyAssembly requires two people 103Operation and Adjustment HOW to Plug in the Power CordSee Features of the ConsoleSteps beginning on Console, remove itDescription of the Console HOW to Turn on the Power HOW to USE the Manual ModeStand on the foot DisplayCalories/Pulse Display AvoidPreset Programs Put on the optional chest pulse sensor Enter a maximum heart rate settingYour exercise heart Select one of the two pulse programsCline will decrease If you increase YouIf you increase Speed willHOW to Connect Your Portable Stereo HOW to Connect Your Portable CD PlayerVideocassettes Plug the adapter into the Line OUT jack on your stereo HOW to Connect Your Home StereoHOW to Connect Your Computer OUT jack on your stereoHOW to Connect Your VCR ProgramsWhen the CD or video program is completed, Next settings of the CD or video programWill change to the next settings of the CD or Make sure that the audio cable is properlyReturn to the treadmill and stand on the foot HOW to USE Programs Directly from OUR Internet SiteNext settings of the program And/or incline changesInformation MODE/DEMO Mode Optional Chest Pulse SensorHOW to Lower the Treadmill for USE HOW to Fold the Treadmill for StorageHOW to Move the Treadmill Carefully move the treadmill to the desired locationPower Cord TROUBLE-SHOOTING and MaintenanceProblemsolution UnplugTion properly Unplug Power CordShifted to the left Make sure that the gap betweenWorkout Guidelines Conditioning GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Key Qty Description Key Limited Warranty HOW to Order Replacement PartsPart No R0801A Remove and Save this Exploded Drawing for Future Reference DRAWING-ModelExploded DRAWING-Model No. HCTL05910
Top Page Image Contents