NordicTrack 831.159770 user manual

Page 15

29.Wrap the High Cable (73) around a 4” Pulley

(35). Attach the Pulley and a Cable Trap (44) to the top hole in the Pulley Bracket (91) attached to the Leg Press Cable (76), with a 3/8” x 1 3/4” Bolt (60) and a 3/8” Nylon Jamnut (63).

30.Route the High Cable (73) up through the next slot in the Top Frame (1) and wrap the Cable around a 4” Pulley (35) in the direction shown.

Attach the 4” Pulley (35) to the Top Frame (1) with a 3/8” x 2 1/2” Bolt (54), two 3/8” Washers (55), two 5/8” x 1/2” Bushings (42), and a 3/8” Nylon Jamnut (63).

31.Route the High Cable (73) around a 4” Pulley (35) and down through the indicated slot in the Top Frame (1).

Attach the 4” Pulley (35) to the Top Frame (1) with a 3/8” x 2 1/2” Bolt (54), two 3/8” Washers (55), two 5/8” x 1/2” Bushings (42), and a 3/8” Nylon Jamnut (63).

Let the High Cable (73) hang over the weight stack; it will be attached in step 38.

32.Locate the Low Cable (72), which has a ball on each end. Route the Low Cable through the slots in the Leg Lever (29) and the Base (8).

Attach a 4” Pulley (35) inside the Leg Lever (29) with a 3/8” x 2 1/2” Bolt (54), two 3/8” Washers (55), two 5/8” x 1/2” Bushings (42), and a 3/8” Nylon Jamnut (63).

Attach the 1/2” x 1 3/4” Bushing (94) inside the bottom of the Leg Lever (29) with a 5/16” x 2 1/2” Bolt (96), two 5/16” Washers (80), and a 5/16” Nylon Jamnut (79). Press a 2” Square Inner Cap

(33)into the bottom of the Leg Lever. Note: It may be easier to attach the 2” Square Inner Cap if you pivot the Leg Lever upward.

29

 

 

 

 

 

35

 

 

 

44

 

 

 

 

73

91

 

 

 

63

 

 

 

 

 

60

 

 

 

76

 

 

 

30

35

73

1

 

 

 

63

 

 

 

 

55

 

 

 

 

42

 

55

 

 

 

 

 

 

 

 

54

 

31

 

 

 

 

63

35

 

1

 

 

 

 

 

55

 

 

 

 

42

 

55

 

 

 

 

 

 

 

42

54

 

 

 

 

 

 

73

 

 

 

32

 

 

 

 

 

 

 

29

 

 

8

 

55

54

 

 

 

 

 

 

 

 

 

 

42

 

 

 

 

 

96

 

 

 

80

 

42

 

 

 

55

 

94

 

 

63

79

80

35

72

 

 

33

 

 

15

Image 15
Contents QUESTIONS? Model No Serial NoCustomer HOT Line Table of Contents Important Precautions Decal Before YOU BeginMake Assembly Easier for Yourself AssemblyFrame Assembly Make sure the large pin groove is oriented as shown Open the parts bag labeled Weight InsertsTighten the 3/8 Nylon Locknuts 50 used in steps 1 Locknut onto the upper Bolt yetHas an extra hole in it Arm AssemblyOpen the parts bags labeled ARM Assem BLYLeg Lever Lock must pivot easily Do not overtighten the Nylon LocknutCable Assembly Page Page Page Page Is oriented so it will hold the Cable in place Two Pulley Plates 31. Make sure the Cable isSeat Assembly AssemblyOpen the parts bag labeled ARM and Seat Page Page Page Cable Diagram Adjusting the Height of the Seat AdjustmentsChanging the Weight Setting Attaching the AccessoriesAttaching the Curl PAD Converting the PRESS/FLY ArmsWeight Resistance Chart Weight Press Low High Leg Plates Arm PulleyLbs Tightening the Cables TROUBLE-SHOOTING and MaintenanceExercise Guidelines Muscle Chart Cooling DownStaying Motivated Limited Warranty Ordering Replacement PartsPage 3 Inner Cap Page Part Identification CHART-Model No .159770 R0402A Remove this Part LIST/EXPLODED Drawing From the Manual Qty Description Part LIST-Model NoExploded 831159770