Bowflex 001-6961 manual Attach the Seat Rail to the Main Assembly, Rail Assembly can move freely

Page 12

Assembly Guide

Step 9 - Attach the Seat Rail to the Main Assembly

Figure 9

Locate the following items:

 

• From Step 4 - Main Assembly

Main

• From Step 8 - Seat Rail Assembly

Assembly

 

• Item #12 - Seat Rail Knob

 

• Item #J - (1) 3/8" X 4 1/4" Button Head Screw

 

• Item #N - (2) 3/8" Washers

 

• Item #O - (1) 3/8" Nylock Nut

Seat Rail

• Item #Q - (1) Bolt Cover

Bracket

 

12

Align the holes on the Seat Rail Assembly (from Step 8)

J

 

with the holes in the Rail Bracket on the Main Assembly

Rail

(from Step 4), as shown in Figure 9.

Assembly

Insert the Seat Rail Assembly into the Seat Rail Bracket,

O

 

and then place (1) 3/8" Washer (Item #N) over the end of (1)

N

 

3/8" X 4 1/4" Button Head Screw (Item #J). Insert the screw

 

through the aligned holes, as shown, and place (1) 3/8"

 

Washer and (1) 3/8" Nylock Nut (Item #O) over the end of the

 

screw to secure.

 

Do not over-tighten the hardware from Step 9.

 

Note: Tighten the nylock nut enough that the threads of the screw

 

extend through the nylock nut, but loosely enough that the Seat

 

Rail Assembly can move freely.

 

At this time, place (1) Bolt Cover (Item #Q) over the Nylock Nut installed during Step 9. Then, thread the Seat Rail Knob (Item #12) into the top hole on the Seat Rail Bracket, as shown in Figure 9, but do not over-tighten.

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Assembly Instructions Bowflex Sport Home GymTable of Contents Safety Precautions Get to Know Your Machine Home GymBasic Assembly Principles Hardware Guide Tools You Will NeedAssembly Guide Attach the Lower Lat Tower to the Base PlatformAttach the Base Legs to the Base Platform Attach the Squat Platform to the Main Assembly Completely tighten hardware installed during StepAttach the Chest Bar with Pulleys to Main Assembly Attach the Seat Bracket to the Seat PadButton Head Screws Item #K one washer per screw Insert the screws through the lined up holes in the ChestAttach the Seat Rail to the Seat Assembly Attach the Rear Leg to the Rear Leg Cross TubeAssembly can move freely Attach the Rear Leg to the Seat RailRail Pull Pin Do not over-tighten hardware from StepAttach the Seat Rail to the Main Assembly Rail Assembly can move freelyDo not over-tighten the hardware from Step Attach the Leg Extension Pivot Tube 10aAttach Leg Cable to the Leg Extension Slide the hooked end of the Leg Cable beneath the LegThread the screw through Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Attach the Leg Extension Seat to the Main Assembly Attach the Lat Cross Bar to the Upper Lat TowerPlace 2 3/8 Washers Item #N over the ends Attach the Rod Box with Power Rods to the Rod Box Frame Attach the Upper Lat Tower to the LowerAttach the Faceplate to the Main Assembly Attach the Rod Box Frame to the Lat TowerBe tightened during Step Attach the Faceplate Back Panels Tighten Lower Bolt on the Seat BracketThem until the panels meet in the center #A, as shown in , attaching one side at a timeAttach the Bench to the Seat Assembly Route the Rod CablesLocate the following items Repeat for remaining Chest Pulley Rod CableRoute the Lat Cables Route the Leg CablesRoute the Squat Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport
Top Page Image Contents