Bowflex Complete Sport Assembly Guide for Your Home Gym
Page 9

Assembly Guide

 

Step 4 - Attach the Chest Bar with Pulleys to the

Figure 4

 

Main Assembly

 

 

Locate the following items:

 

Chest Bar

 

K

• From Step 3 - Main Assembly

Brackets

 

 

• Item #6 - Chest Bar w/ Pulleys - Do not unwrap cables!

 

6

• Item #K - (2) 3/8" X 5" Button Head Screws

 

 

 

• Item #N - (4) 3/8" Washers

 

 

• Item #O - (2) 3/8" Nylock Nuts

N

 

 

 

Line up the bolt holes in the brackets on the Chest Bar

 

 

with Pulleys (Item #6) with the lowest bolt holes on the

 

 

Lower Lat Tower, as shown in Figure 4. Pulleys should be

 

 

oriented forward.

 

O

Place (2) 3/8" Washers (Item #N) over the end of (2) 3/8” X

 

Base Platform/

5" Button Head Screws (Item #K) - one washer per screw.

 

Lower Lat Tower

Insert the screws through the lined up holes in the Chest

 

Assembly

 

 

Bar with Pulleys and the Lower Lat Tower, and secure each

 

 

screw by placing (1) 3/8" Washers and (1) 3/8" Nylock Nuts

 

 

(Item #O) over the end of each screw.

 

 

Completely tighten hardware installed during Step 4.

 

 

Step 5 - Attach the Seat Bracket to the Seat Pad

Locate the following items:

•Item #7 - Seat Pad

•Item #8 - Seat Bracket

•Item #C - (4) 5/16" X 3/4" Button Head Screws

•Item #M - (4) 5/16" Washers

Place the Seat Pad (Item #7) on the floor, cushion-side down. Position the Seat Bracket (Item #8) so the cut-out is toward the angled edge of the Seat Pad. Align the four holes in the Seat Bracket with the four holes in the Seat Pad.

Place (4) 5/16"Washers (Item #M) over (4) 5/16" X 3/4" Button Head Screws (Item #C) - one over each screw, and use those screws to secure the Seat Bracket to the Seat Pad.

Completely tighten hardware installed during Step 5.

Figure 5

 

 

C

M

8

 

 

Cut-out

7

 

 

Angled

 

Edge

7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Bowflex Sport Home Gym Assembly InstructionsTable of Contents Safety Precautions Home Gym Get to Know Your MachineBasic Assembly Principles Tools You Will Need Hardware GuideAssembly Guide Attach the Lower Lat Tower to the Base PlatformAttach the Base Legs to the Base Platform Completely tighten hardware installed during Step Attach the Squat Platform to the Main AssemblyAttach the Seat Bracket to the Seat Pad Attach the Chest Bar with Pulleys to Main AssemblyButton Head Screws Item #K one washer per screw Insert the screws through the lined up holes in the ChestAttach the Rear Leg to the Rear Leg Cross Tube Attach the Seat Rail to the Seat AssemblyAttach the Rear Leg to the Seat Rail Assembly can move freelyRail Pull Pin Do not over-tighten hardware from StepAttach the Seat Rail to the Main Assembly Rail Assembly can move freelyDo not over-tighten the hardware from Step 10a Attach the Leg Extension Pivot TubeSlide the hooked end of the Leg Cable beneath the Leg Attach Leg Cable to the Leg ExtensionThread the screw through Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Attach the Leg Extension Seat to the Main Assembly Attach the Lat Cross Bar to the Upper Lat TowerPlace 2 3/8 Washers Item #N over the ends Attach the Upper Lat Tower to the Lower Attach the Rod Box with Power Rods to the Rod Box FrameAttach the Faceplate to the Main Assembly Attach the Rod Box Frame to the Lat TowerBe tightened during Step Tighten Lower Bolt on the Seat Bracket Attach the Faceplate Back PanelsThem until the panels meet in the center #A, as shown in , attaching one side at a timeRoute the Rod Cables Attach the Bench to the Seat AssemblyLocate the following items Repeat for remaining Chest Pulley Rod CableRoute the Leg Cables Route the Lat CablesRoute the Squat Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport
Top Page Image Contents