Bowflex 001-6961 manual Attach the Leg Extension Seat to the Main Assembly

Page 16

Assembly Guide

Step 14 - Attach the Leg Extension Seat to the Main Assembly

Locate the following items:

•From Step 13 - Leg Extension Seat Assembly

•From Step 12 - Main Assembly

The Leg Extension Seat Assembly is removable, and can be attached to the Rear Leg Assembly easily by placing the Rail Bracket Hooks over the Rear Rollers.

Place the Rail Bracket Hooks onto the Roller Tube Spacers (sandwiched between the Rear Leg and the Foam Rollers).

Once the Support Tube Bracket Hooks connect with the Roller Tube Spacers, slightly “roll” the back edge of the Seat down to lock into place.

Warning: For your safety, always ensure that the Support Tube Bracket Hooks fully engage with the Roller Tube Spacers.

To remove the Leg Extension Seat Assembly, reverse this procedure.

Figure 14

Leg Extension

Seat

Support Tube

Bracket Hooks

Roller Tube

Spacers

Back Edge

Step 15 - Attach the Lat Cross Bar to the Upper Lat Tower

Locate the following items:

•Item #22 - Lat Cross Bar - Do not unwrap cables!

•Item #23 - Upper Lat Tower

•Item #H - (2) 3/8" X 3" Button Head Screws

•Item #N - (4) 3/8" Washers

•Item #O - (2) 3/8" Nylock Nuts

Align the holes in the Lat Cross Bar (Item #22) with the holes in the bracket on the Upper Lat Tower (Item #23).

Place (2) 3/8" Washers (Item #N) over the ends of

(2)3/8" X 3" Button Head Screws (Item #H) - one washer per screw. Thread the screws through the aligned holes, then secure by placing (1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over each screw and tighten.

Completely tighten hardware installed during Step 15.

Figure 15	22
	22
	O
	N
	H
	Lat
	Tower
	Bracket
	23

14

Image 16

Contents Assembly Instructions Bowflex Sport Home GymTable of Contents Safety Precautions Get to Know Your Machine Home GymBasic Assembly Principles Hardware Guide Tools You Will NeedAttach the Lower Lat Tower to the Base Platform Assembly GuideAttach the Base Legs to the Base Platform Attach the Squat Platform to the Main Assembly Completely tighten hardware installed during StepAttach the Chest Bar with Pulleys to Main Assembly Attach the Seat Bracket to the Seat PadButton Head Screws Item #K one washer per screw Insert the screws through the lined up holes in the ChestAttach the Seat Rail to the Seat Assembly Attach the Rear Leg to the Rear Leg Cross TubeAssembly can move freely Attach the Rear Leg to the Seat RailRail Pull Pin Do not over-tighten hardware from StepRail Assembly can move freely Attach the Seat Rail to the Main AssemblyDo not over-tighten the hardware from Step Attach the Leg Extension Pivot Tube 10aAttach Leg Cable to the Leg Extension Slide the hooked end of the Leg Cable beneath the LegThread the screw through Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Attach the Lat Cross Bar to the Upper Lat Tower Attach the Leg Extension Seat to the Main AssemblyPlace 2 3/8 Washers Item #N over the ends Attach the Rod Box with Power Rods to the Rod Box Frame Attach the Upper Lat Tower to the LowerAttach the Rod Box Frame to the Lat Tower Attach the Faceplate to the Main AssemblyBe tightened during Step Attach the Faceplate Back Panels Tighten Lower Bolt on the Seat BracketThem until the panels meet in the center #A, as shown in , attaching one side at a timeAttach the Bench to the Seat Assembly Route the Rod CablesLocate the following items Repeat for remaining Chest Pulley Rod CableRoute the Lat Cables Route the Leg CablesRoute the Squat Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport