Bowflex 001-6961 manual Route the Lat Cables, Route the Leg Cables, Route the Squat Cables

Page 21

Assembly Guide

Step 24 - Route the Lat Cables

Locate the following items:

•Item #S - (2) Hand Grips

•Item #R - (1) Bent Lat Bar (optional)

•Item #Z - (2) Lat Cables with (2) Snap Hooks (attached)

Unwrap the Lat Cables with Snap Hooks from both Pulleys on the Lat Cross Bar. Pull one end of the Cables down from the Lat Cross Bar, and fasten to the Chest Cable Snap Hook.

Fasten the attached Snap Hook from the Lat Cable to a Hand Grip or the Bent Lat Bar. Repeat for remaining Lat Cable.

Figure 24 - Lat Cables

Snap

Hook

Hand Grips

or Bent

Lat Bar

Snap

Hook

Step 25 - Route the Leg Cables

Locate the following items:

•Item #AA - Leg Cable

•From Step 14 - Leg Extension Seat Assembly

Unwrap the Cables from the Rear Leg Pulley.

Pull one end of the “Y” Cable away from the Rear Leg to fasten to a Snap Hook on the Rod Cable.

Note: For this step, make sure your Leg Extension Seat is installed.

Figure 25 - Leg Cables

Snap

Hook

Leg

Extension

Seat

Step 26 - Route the Squat Cables

Figure 26 - Squat Cables

 

Locate the following items:

Squat Bar

• Item #R - Squat Bar

 

Unwrap the Cables on each Base Leg Pulley. Pull one end of the

 

Cable up from the Leg Pulley, and fasten the Cable to a Snap

 

Hook on the Chest Bar.

 

Fasten the Snap Hook attached to the Squat Cables to the

 

corresponding Squat Bar “D” Ring.

Snap

 

Hook

Repeat for remaining Squat Cable.

Snap

 

 

Hook

CONGRATULATIONS! You have successfully completed assembly

 

of your Bowflex Sport® Home Gym! Please inspect your machine

 

to ensure that all fasteners are tight and everything is properly

 

assembled. Review all warnings that are affixed to the machine.

19

 

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Bowflex Sport Home Gym Assembly InstructionsTable of Contents Safety Precautions Home Gym Get to Know Your MachineBasic Assembly Principles Tools You Will Need Hardware GuideAssembly Guide Attach the Lower Lat Tower to the Base PlatformAttach the Base Legs to the Base Platform Completely tighten hardware installed during Step Attach the Squat Platform to the Main AssemblyAttach the Seat Bracket to the Seat Pad Attach the Chest Bar with Pulleys to Main AssemblyButton Head Screws Item #K one washer per screw Insert the screws through the lined up holes in the ChestAttach the Rear Leg to the Rear Leg Cross Tube Attach the Seat Rail to the Seat AssemblyAttach the Rear Leg to the Seat Rail Assembly can move freelyRail Pull Pin Do not over-tighten hardware from StepAttach the Seat Rail to the Main Assembly Rail Assembly can move freelyDo not over-tighten the hardware from Step 10a Attach the Leg Extension Pivot TubeSlide the hooked end of the Leg Cable beneath the Leg Attach Leg Cable to the Leg ExtensionThread the screw through Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Attach the Leg Extension Seat to the Main Assembly Attach the Lat Cross Bar to the Upper Lat TowerPlace 2 3/8 Washers Item #N over the ends Attach the Upper Lat Tower to the Lower Attach the Rod Box with Power Rods to the Rod Box FrameAttach the Faceplate to the Main Assembly Attach the Rod Box Frame to the Lat TowerBe tightened during Step Tighten Lower Bolt on the Seat Bracket Attach the Faceplate Back PanelsThem until the panels meet in the center #A, as shown in , attaching one side at a timeRoute the Rod Cables Attach the Bench to the Seat AssemblyLocate the following items Repeat for remaining Chest Pulley Rod CableRoute the Leg Cables Route the Lat CablesRoute the Squat Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport
Top Page Image Contents