Bowflex 001-6961 manual Attach the Upper Lat Tower to the Lower

Page 17

Assembly Guide

Step 16 - Attach the Upper Lat Tower to the Lower

Locate the following items:

•From Step 15 - Upper Lat Tower Assembly

•From Step 14 - Main Assembly

•Item #E - (6) 3/8" X 3/4" Button Head Screw

•Item #N - (6) 3/8" Washers

Carefully insert the end of the Upper Lat Tower into the open end of the Lower Lat Tower. Align the holes on the Upper Lat Tower with the holes on the Lower Lat Tower.

Place (6) 3/8" Washers (Item #N) over the ends of (6) 3/8" X 3/4" Button Head Screws (Item #E) - one washer per screw. Thread the screws into the aligned holes, as shown in Figure 16.

Completely tighten hardware installed during Step 16.

Figure 16

Upper Lat

Tower

N

E

Lower Lat

Tower

Step 17 - Attach the Rod Box with Power Rods® to the Rod Box Frame

Locate the following items:

•Item #24 - Rod Box Frame

•Item #25 - Rod Box with Power Rods®

•Item #B - (3) #10 X 1" Phillips Head Screws

•Item #L - (3) 1/4" Washers

Place the Rod Box Frame (Item #24) and Rod Box with

Power Rods® (Item #25) onto one side as shown in Figure 17. Slide the Rod Box with Power Rods® into the Rod Box Frame until the Rod Box is completely seated in the Rod Box Frame.

Place (3) 1/4" Washers (Item #L) over the ends of (3) #10 X 1" Phillips Head Screws (Item #B) - one washer per screw. Insert the screws through the slot on the Rod Box Frame and thread into the holes in the Rod Box with Power Rods®.

Completely tighten hardware installed during Step 17.

Figure 17

24

L

B

Slot

25

15

Image 17

Contents Bowflex Sport Home Gym Assembly InstructionsTable of Contents Safety Precautions Home Gym Get to Know Your MachineBasic Assembly Principles Tools You Will Need Hardware GuideAttach the Base Legs to the Base Platform Assembly GuideAttach the Lower Lat Tower to the Base Platform Completely tighten hardware installed during Step Attach the Squat Platform to the Main AssemblyAttach the Seat Bracket to the Seat Pad Attach the Chest Bar with Pulleys to Main AssemblyButton Head Screws Item #K one washer per screw Insert the screws through the lined up holes in the ChestAttach the Rear Leg to the Rear Leg Cross Tube Attach the Seat Rail to the Seat AssemblyAttach the Rear Leg to the Seat Rail Assembly can move freelyRail Pull Pin Do not over-tighten hardware from StepDo not over-tighten the hardware from Step Attach the Seat Rail to the Main AssemblyRail Assembly can move freely 10a Attach the Leg Extension Pivot TubeSlide the hooked end of the Leg Cable beneath the Leg Attach Leg Cable to the Leg ExtensionThread the screw through Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Place 2 3/8 Washers Item #N over the ends Attach the Leg Extension Seat to the Main AssemblyAttach the Lat Cross Bar to the Upper Lat Tower Attach the Upper Lat Tower to the Lower Attach the Rod Box with Power Rods to the Rod Box FrameBe tightened during Step Attach the Faceplate to the Main AssemblyAttach the Rod Box Frame to the Lat Tower Tighten Lower Bolt on the Seat Bracket Attach the Faceplate Back PanelsThem until the panels meet in the center #A, as shown in , attaching one side at a timeRoute the Rod Cables Attach the Bench to the Seat AssemblyLocate the following items Repeat for remaining Chest Pulley Rod CableRoute the Leg Cables Route the Lat CablesRoute the Squat Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport