Bowflex 001-6961 Attach the Rear Leg to the Seat Rail, Rail Pull Pin, Assembly can move freely

Page 11

Assembly Guide

 

 

Step 8 - Attach the Rear Leg to the Seat Rail

Figure 8

 

 

Locate the following items:

 

 

 

• From Step 6 - Seat Rail Assembly

 

 

 

• From Step 7 - Rear Leg Assembly

 

 

 

• Item #J - (1) 3/8" X 4 1/4" Button Head Screw

 

 

End

• Item #N - (2) 3/8" Washers

 

 

 

 

Bracket

• Item #O - (1) 3/8" Nylock Nut

 

 

 

• Item #Q - (2) Bolt Covers

 

 

O

Undo the twist ties from the Pivot Bushings on the end of the Rear

Rail

 

 

Assembly

 

 

 

 

 

Leg Assembly (from Step 6), but do not remove the Bushings.

 

N

 

 

 

 

Note: When attaching the Rear Leg Assembly (from Step 7) to

 

 

 

the Seat Rail Assembly, rotate the Rear Leg forward (as shown

 

 

Middle

in Figure 8b), to allow the Leg Latch to engage with the Seat

 

 

 

J

Hole

 

 

Rail Pull Pin.

 

 

 

 

 

Align the holes on the End Bracket of the Seat Rail Assembly with

 

 

 

the middle holes on the Rear Leg Assembly, (see Figure 8).

 

Rear Leg

 

Assembly

 

 

Place (1) 3/8" Washer (Item #N) over the end of (1) 3/8" X 4 1/4"

 

 

 

Button Head Screw (Item #J). Insert the screw through the lined

 

 

 

up holes and then loosely secure on the opposite side by placing (1)

 

 

 

3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the end.

 

 

 

Do not over-tighten hardware from Step 8.

Figure 8b

 

 

Rail

 

 

 

Leg Latch

 

Note: Tighten the nylock nut enough that the threads of the screw

Assembly

 

 

 

 

 

 

extend through the nylock nut, but loosely enough that the Leg

 

 

 

Assembly can move freely.

 

 

 

At this time, place (1) Bolt Cover (Item #Q) over the Nylock Nut installed during Step 8, place 1 bolt cover over the Nylock Nut going through the rear leg pulley.

Once you have completed Step 8, rotate the Rear Leg back until it engages the Seat Rail Pull Pin.

Seat Rail Pull Pin

Rear Leg

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Bowflex Sport Home Gym Assembly InstructionsTable of Contents Safety Precautions Home Gym Get to Know Your MachineBasic Assembly Principles Tools You Will Need Hardware GuideAttach the Base Legs to the Base Platform Assembly GuideAttach the Lower Lat Tower to the Base Platform Completely tighten hardware installed during Step Attach the Squat Platform to the Main AssemblyInsert the screws through the lined up holes in the Chest Attach the Chest Bar with Pulleys to Main AssemblyAttach the Seat Bracket to the Seat Pad Button Head Screws Item #K one washer per screwAttach the Rear Leg to the Rear Leg Cross Tube Attach the Seat Rail to the Seat AssemblyDo not over-tighten hardware from Step Assembly can move freelyAttach the Rear Leg to the Seat Rail Rail Pull PinDo not over-tighten the hardware from Step Attach the Seat Rail to the Main AssemblyRail Assembly can move freely 10a Attach the Leg Extension Pivot TubeHoles in the Leg Extension and cable end. Place 1 3/8 Attach Leg Cable to the Leg ExtensionSlide the hooked end of the Leg Cable beneath the Leg Thread the screw throughAssemble the Leg Extension Seat Place 2 3/8 Washers Item #N over the ends Attach the Leg Extension Seat to the Main AssemblyAttach the Lat Cross Bar to the Upper Lat Tower Attach the Upper Lat Tower to the Lower Attach the Rod Box with Power Rods to the Rod Box FrameBe tightened during Step Attach the Faceplate to the Main AssemblyAttach the Rod Box Frame to the Lat Tower #A, as shown in , attaching one side at a time Attach the Faceplate Back PanelsTighten Lower Bolt on the Seat Bracket Them until the panels meet in the centerRepeat for remaining Chest Pulley Rod Cable Attach the Bench to the Seat AssemblyRoute the Rod Cables Locate the following itemsRepeat for remaining Squat Cable Route the Lat CablesRoute the Leg Cables Route the Squat CablesOffices in the United States International Offices Page Sport
Top Page Image Contents