Bowflex 001-6961 manual Attach the Leg Extension Pivot Tube, 10a

Page 13

Assembly Guide
Step 10 - Attach the Leg Extension Pivot Tube	Figure 10a	G	Bracket
			Bracket
Locate the following items:
Locate the following items:		N
• Item #13 - Leg Extension Pivot Tube		N
• Item #13 - Leg Extension Pivot Tube			O
• From Step 9 - Main Assembly
• Item #30 - Lock Out Pin
• Item #G - (1) 3/8" X 2 3/4" Button Head Screw		“Curve”
• Item #N - (2) 3/8" Washers
• Item #O - (1) 3/8" Nylock Nut
• Item #Q - (1) Bolt Cover
Undo the twist ties from the Pivot Bushings. Align the holes		13

located on the“curve” of the Leg Extension PivotTube (Item #13)
with the holes on the bracket of the Rear Leg, as shown in Figure			Rear Leg

10a.
Place (1) 3/8" Washer (Item #N) over the end of (1) 3/8" X
2 3/4" Button Head Screw (Item #G). Thread the screw
through the aligned holes and bushings and secure by
placing (1) 3/8" Washer and (1) 3/8" Nylock Nut (Item #O)
over the end of the screw, as shown in Figure 10a.
Do not over-tighten hardware from Step 10.	Figure 10b
	Figure 10b

Place (1) Bolt Cover (Item #Q) over the Nylock Nut installed during Step 10.

Note: When storing the Rail Assembly, insert the Lock Out Pin (Item #30) through the holes in the Pivot Tube to temporarily hold the Leg Extension in place while folding the Rail up (see Figure 10b).

Holes

30

Leg Extension

11

Image 13

Contents Bowflex Sport Home Gym Assembly InstructionsTable of Contents Safety Precautions Home Gym Get to Know Your MachineBasic Assembly Principles Tools You Will Need Hardware GuideAttach the Lower Lat Tower to the Base Platform Assembly GuideAttach the Base Legs to the Base Platform Completely tighten hardware installed during Step Attach the Squat Platform to the Main AssemblyAttach the Seat Bracket to the Seat Pad Attach the Chest Bar with Pulleys to Main AssemblyButton Head Screws Item #K one washer per screw Insert the screws through the lined up holes in the ChestAttach the Rear Leg to the Rear Leg Cross Tube Attach the Seat Rail to the Seat AssemblyAttach the Rear Leg to the Seat Rail Assembly can move freelyRail Pull Pin Do not over-tighten hardware from StepRail Assembly can move freely Attach the Seat Rail to the Main AssemblyDo not over-tighten the hardware from Step 10a Attach the Leg Extension Pivot TubeSlide the hooked end of the Leg Cable beneath the Leg Attach Leg Cable to the Leg ExtensionThread the screw through Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Attach the Lat Cross Bar to the Upper Lat Tower Attach the Leg Extension Seat to the Main AssemblyPlace 2 3/8 Washers Item #N over the ends Attach the Upper Lat Tower to the Lower Attach the Rod Box with Power Rods to the Rod Box FrameAttach the Rod Box Frame to the Lat Tower Attach the Faceplate to the Main AssemblyBe tightened during Step Tighten Lower Bolt on the Seat Bracket Attach the Faceplate Back PanelsThem until the panels meet in the center #A, as shown in , attaching one side at a timeRoute the Rod Cables Attach the Bench to the Seat AssemblyLocate the following items Repeat for remaining Chest Pulley Rod CableRoute the Leg Cables Route the Lat CablesRoute the Squat Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport