Bowflex 001-6961 manual Attach the Faceplate to the Main Assembly, Be tightened during Step

Page 18

Assembly Guide

Step 18 - Attach the Rod Box Frame to the Lat Tower

Figure 18

Locate the following items:

 

• From Step 16 - Main Assembly

 

• From Step 17 - Rod Box/Frame Assembly

 

Item #K - (2) 3/8" X 5" Button Head Screws

K

Item #N - (4) 3/8" Washers

Rod Box

Brackets

Item #O - (2) 3/8" Nylock Nuts

N

 

Align the bolt holes on the Rod Box brackets with the bolt

 

holes on the Lat Tower above the Chest Bar , as shown in

 

Figure 18.

 

Place (2) 3/8" Washers (Item #N) over the ends of

 

(2) 3/8" X 5" Button Head Screws (Item #K) - one washer per

 

screw. Insert the screws through the aligned holes. Place (1)

Chest Bar

3/8" Washer and (1) 3/8" Nylock Nut (Item #O) over the end of

 

each screw and tighten.

 

Completely tighten hardware installed during Step 18.

O

 

Step 19 - Attach the Faceplate to the Main

Figure 19

 

Assembly

Faceplate

Locate the following items:

“Stems”

 

Item #26 - Faceplate

 

• From Step 18 - Main Assembly

 

Item #A - (2) #10 Phillips Head Screws

 

Position the textured side of the Faceplate (Item #26) against

 

the Lower Lat Tower. Insert the plastic“stems” through the

26

corresponding holes on the Lower Lat Tower, as shown in Figure

 

19. You may need to push the Power Rods® out of the way to

 

insert the screws into the holes.

 

Attach the Faceplate to the Lower Lat Tower by threading (2)

A

 

#10 Phillips Head Screws (Item #A) into the “stems”.

 

Do not completely tighten hardware installed during Step 19 -

 

tighten screws approximately 1/2 of completion. Hardware will

 

be tightened during Step 20.

 

16

 

Image 18
Contents Assembly Instructions Bowflex Sport Home GymTable of Contents Safety Precautions Get to Know Your Machine Home GymBasic Assembly Principles Hardware Guide Tools You Will NeedAssembly Guide Attach the Lower Lat Tower to the Base PlatformAttach the Base Legs to the Base Platform Attach the Squat Platform to the Main Assembly Completely tighten hardware installed during StepButton Head Screws Item #K one washer per screw Attach the Chest Bar with Pulleys to Main AssemblyAttach the Seat Bracket to the Seat Pad Insert the screws through the lined up holes in the ChestAttach the Seat Rail to the Seat Assembly Attach the Rear Leg to the Rear Leg Cross TubeRail Pull Pin Assembly can move freelyAttach the Rear Leg to the Seat Rail Do not over-tighten hardware from StepAttach the Seat Rail to the Main Assembly Rail Assembly can move freelyDo not over-tighten the hardware from Step Attach the Leg Extension Pivot Tube 10aThread the screw through Attach Leg Cable to the Leg ExtensionSlide the hooked end of the Leg Cable beneath the Leg Holes in the Leg Extension and cable end. Place 1 3/8Assemble the Leg Extension Seat Attach the Leg Extension Seat to the Main Assembly Attach the Lat Cross Bar to the Upper Lat TowerPlace 2 3/8 Washers Item #N over the ends Attach the Rod Box with Power Rods to the Rod Box Frame Attach the Upper Lat Tower to the LowerAttach the Faceplate to the Main Assembly Attach the Rod Box Frame to the Lat TowerBe tightened during Step Them until the panels meet in the center Attach the Faceplate Back PanelsTighten Lower Bolt on the Seat Bracket #A, as shown in , attaching one side at a timeLocate the following items Attach the Bench to the Seat AssemblyRoute the Rod Cables Repeat for remaining Chest Pulley Rod CableRoute the Squat Cables Route the Lat CablesRoute the Leg Cables Repeat for remaining Squat CableOffices in the United States International Offices Page Sport